Sourcetronic ST9201 Series User Manual Download Page 34

Page: 34 / 94

◇

Press F5 (ALT) to select all the files or not. If the cursor is in the RAM FILE area,

press F5 key to select all or none of the non-empty files in the RAM FILE area. As

shown below:

RAM FILE

USB FILE



00:

IR500V

√

00:

blank

01:

blank

01:

blank

02:

DC2000V

√

02:

blank

03:

AC1000V

√

03:

blank

04:

blank

04:

blank

COPY

PAST

DELE

SELE

ALT

Copy files

When you choose one or more of your files, press F1 (COPY) to copy the selected

file to the instrument's BUFF.

Paste files

When you copy your file, move the cursor to the place you want to paste, press the
F2 key (PAST) to paste. For example, paste the three files in RAM FILE into the

USB: copy the three files selected and move the cursor to the USB FILE area, press

the F2 key (PAST) to paste. As shown below:

RAM FILE

USB FILE

00:

IR500V



00:

IR500V

01:

blank

01:

blank

02:

DC2000V

02:

DC2000V

03:

AC1000V

03:

AC1000V

04:

blank

04:

blank

COPY

PAST

DELE

SELE

ALT

NOTE:when moving the stored record, they can only be stored to the

corresponding item. For example, 00 archive file can only be stored to 00
file.

Delete files
It is only valid in USB FILE area. Move the cursor to the file you want to delete,

press F4 (DELE) to delete the file.

Summary of Contents for ST9201 Series































































































Search results

Summary of Contents for ST9201 Series

Reviews:

Related manuals for ST9201 Series

Brands by name

Popular brands

Sourcetronic ST9201 Series, User Manual

Search results

Summary of Contents for ST9201 Series

Reviews:

Related manuals for ST9201 Series

Brands by name

Popular brands