background image

Service Record Mio Carbon (Design 2018)

11 of 28

2020-09-01

(1)

 The wheelchair is delivered by us in such 

a way that the spacer bushing 

(B)

 required 

for seat widening sit on the inside of the side 

panel holders

 (D)

.

•  (1)

 Completely remove screw connec-

tions

 (A)

 and spacer bushing

 (B)

 on 

both sides.

•  Place spacers bushing between side gu-

ard 

(C) 

and side guard brackets 

(D)

,

•  Fit the side guard back to the side gu-

ard holders 

(D)

,

•  Replace all screw connections and tigh-

ten tightly.

•  After the seat widening the spacer bus-

hing must sit on the outside between 

the side holder and side guard.

Then mount the seat plate in the new position:

•  (2)

 Mount the seat plate in the internal 

holes 

(B)

 of the seat support brackets.

•  Reinstall screw connections and tighten 

tightly.

Then mount the back of the firm curved back 

plate in the new position:

•  (3) 

Mount the depression on the inner 

holes 

(B)

 of the back support brackets 

(C)

.

•  Reinstall screw connections and tighten 

tightly.

3.2.5  Side guard/ spacer bushing

3.2  Assembly group seat

(1)

(D)

(D)

(A)

(A)

(B)

(B)

(C)

(2)

Blick unter die Sitzplatte

(A) (B)

(C)

(A)

(B)

(C)

(3)

3.2.6  Adjust quick-release axle

Correct the distance of the  wheels to the side part. Proceed as described above.

Summary of Contents for Mio Carbon





























Reviews: