background image

Service Record Loop

SORG

 RS

33 of 40

2019-07-16

3.8.3  Outdoor Front End

The greater the seat tilt angle, the higher 

the tractability but also the more wobbly the 

wheelchair!

(1)

 Setting the height of the casters:

•  Remove the axle with the screw

 (A)

,

•  place the axle in the alternative holes 

(B) 

of the caster fork and

•  retighten the screw 

(A)

.

(1)

 Setting the length and/or width:

•  In order to change the length between 

the wheelchair and caster remove the 

screws 

(C)

 on both sides,

•  telescope the outdoor front end along 

the alternative holes 

(D)

 to the length 

wanted,

•  replace the screws 

(C)

 and retighten 

them.

•  In order to change width of the out-

door front end, proceed the same way 

with the screws 

(E)

 along the alternative 

holes 

(F)

.

(C)

(E)

(D)

(F)

(1)

(B)

3.8

  

Assembly Group Frame equipment

(A)

The screw pairs 

(A)

 and 

(B) 

must be moved parallel and symmetrical. There must be at 

least one hole free between the screws of each screw pair 

The tilting behavior changes crucially when using the outdoor front end and must be 

practiced! 

Summary of Contents for Loop RS









































Reviews: