Cha
p
te
r 4
Rec
o
rd
ing/
Pl
a
y
bac
k
51
4-2 Playback
3
If you selected “VAR” in step
2
, set the parameter
value by holding down the corresponding button and
rotating the jog dial, while viewing the video.
Setting values vary with the rotation speed of the jog
dial.
4
Repeat steps
2
and
3
as required to set other
parameters.
5
Press the STATUS button to return to the normal
screen.
4-2-2 Playback Operation
This section describes the following types of playback:
• Normal playback
Playback at normal (±1) speed
• Playback in jog mode
Variable speed playback, with the speed determined by
the speed of turning the jog dial
• Playback in shuttle mode
Variable speed playback, with the speed determined by
the angular position of the shuttle dial
Normal playback
First insert a disc.
For details of how to insert a disc, see 3-6-4 “Loading and
Unloading a Disc” on page 38.
To start playback
Press the PLAY button.
Playback starts.
When two or more clips are recorded on the disc, they are
played back continuously.
Note
No audio is output when non-audio signals are played
back.
To jump to the next or previous clip, then start
playback
Use the PREV button, NEXT button, jog dial, or shuttle
dial.
For information about the functions of these buttons, see
“5 Recording and playback control section” on page 16.
For details of the jog and shuttle dials, see “3 Jog/shuttle
control block” on page 14.
To stop playback
Press the STOP button.
If you play back to the end of the last clip
Playback automatically stops.
If, in this state, you press the PLAY button, the message
“ALARM DISC END.” appears on the monitor.
To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
To record an essence mark
While playing back a disc, you can record essence marks
such as shot mark 1 and shot mark 2 in desired frames.
To record a shot mark 1 or shot mark 2, hold down the
F
/
MARK1 or
f
/MARK2 button and press the SET button.
Note
To erase or change essence marks, use the supplied
PDZ-1 Proxy Browsing Software.
Playback in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
±1 times normal speed.
To carry out playback in jog mode, proceed as follows.
1
Press the JOG button, turning it on.
2
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
When extended menu item 101 “SELECTION FOR
SEARCH DIAL ENABLE” is set to “dial” (factory default
ACCESS
SHUTTLE
JOG
THUMB
NAIL
ESSENCE
MARK
MENU
S.SEL
SET
RESET
SHIFT
TOP
F REV
ALL/CH-1
CH-2
CH-3
CH-4
TC
F FWD
AUDIO
END
REC
PRESET
VARIABLE
PB
PREV
NEXT
PLAY
STOP
REC
CLIP
MENU
SYSTEM
MENU
MONITOR
SEL
METER
SEL
HOLD
COUNTER
SEL
SUB
CLIP
MARK1
MARK2
IN
OUT
KEY INHI
ON
OFF
NETWORK
LOCAL
REMOTE
F-RUN
R-RUN
PRESET
REGEN
INT
EXT
RP188
L/ST/R
F
/MARK1 button and
f
/MARK2 button
Jog dial
STOP button
NEXT button
PLAY button
PREV button
Shuttle dial
ACCESS
SHUTTLE
JOG
THUMB
NAIL
ESSENCE
MARK
MENU
S.SEL
SET
RESET
SHIFT
TOP
F REV
ALL/CH-1
CH-2
CH-3
CH-4
TC
F FWD
AUDIO
END
REC
PRESET
VARIABLE
PB
PREV
NEXT
PLAY
STOP
REC
CLIP
MENU
SYSTEM
MENU
MONITOR
SEL
METER
SEL
HOLD
COUNTER
SEL
SUB
CLIP
MARK1
MARK2
IN
OUT
KEY INHI
ON
OFF
NETWORK
LOCAL
REMOTE
F-RUN
R-RUN
PRESET
REGEN
INT
EXT
RP188
L/ST/R
1 2,3
