Sony URX-P40, Operating Instructions Manual

Page: 48 / 56

48
There is no sound. The channel setting on the transmitter is different
from that on the tuner. Use the same channel setting on both the
transmitter and tuner.
The transmitter is not transmitting signals, or the
transmission output is weak. Confirm that the transmitter is turned on.
Alternatively, reduce the distance between the
transmitter and tuner.
The transmitter is set to line level input.
2) Switch to microphone input (page 42) .
The compander mode setting on the transmitter is
different from that on the tuner. Use the same compander mode setting on both
the transmitter and tuner (UTX-B40/M40/P40:
page 43 , URX-P40: page 33 , URX-P41D:
page 38 ).
The transmitter is muted.
1) Press the POWER/MUTE button on the
transmitter to release the muted state.
The MUTE SETTING menu (POWER/MUTE
menu on the UTX-M40) is set to PTT HOLD.
Change the setting
(page 42) .
The audio output connector settings are
incorrect.
7)
Set the audio output connector settings in the
OUTPUT ASSIGN menu
(page 38) .
The Analog/Digital switch of the SMAD-P5 (option)
is not set correctly. Refer to the SMAD-P5 (option) operating
instructions and change to the correct setting.
3)
If no sound is emitted from the microphone
connected to the MIC INPUT connector, the
external microphone is set to OFF or the
microphone type is set incorrectly.
7)
Configure the microphone setting to match the
type of microphone using the MIC SELECT menu
(page 38) .
The sound is weak. The attenuation level on the transmitter is too high. The input level of the transmitter is low. Set the
attenuation of the transmitter to an appropriate
level
(page 41) .
The volume on the amplifier or mixer is low. Adjust the volume to an appropriate level.
The transmitter is set to line level input.
2) Switch to microphone input (page 42) .
The compander mode setting on the transmitter is
different from that on the tuner. Use the same compander mode setting on both
the transmitter and tuner (UTX-B40/M40/P40:
page 43 , URX-P40: page 33 , URX-P41D:
page 38 ).
The supplied cable and the connected device are
not connected correctly. Check the operating instructions for the connected
device and connect the device correctly.
If the sound emitted from the microphone
connected to the MIC INPUT connector is low, the
configured level does not match the connected
microphone.
7)
Adjust the level according to the connected
microphone using the INPUT LEVEL menu
(page 39) .
The sound is
distorted. The attenuation level on the transmitter is too low
or is set to 0. The input level is extremely high. Set the
attenuation on the transmitter so that the audio is
not distorted
(page 41) .
The GAIN MODE menu of the transmitter is set to
15dB BOOST. The input level is extremely high. Change the
GAIN MODE setting so that the sound is not
distorted
(page 41) .
The channel setting on the transmitter is different
from that on the tuner. Use the same channel setting on both the
transmitter and tuner.
Headphones with a monaural mini jack are being
used.
3)
Use headphones with a stereo mini jack.
The OUTPUT MODE menu of the tuner is set to
HIGH GAIN.
7)
The output level is extremely high. Change the
OUTPUT MODE setting to NORMAL so that the
sound is not distorted
(page 34) .
If the sound emitted from the microphone
connected to the MIC INPUT connector is
distorted, the microphone type is set incorrectly.
7)
Configure the microphone setting to match the
type of microphone using the MIC SELECT menu
(page 38) .
The attenuator cannot
be set. The GAIN MODE menu is set to AUTO GAIN, or
the INPUT LEVEL menu is set to LINE. Change the GAIN MODE menu and INPUT
LEVEL menu settings
(page 41) .
Symptom Cause Solution