background image

54

Approx. 7 hours with output power of 

10 mW (E, KR models)

Dimensions

38 × 98 × 38 mm (1 

1

/

2

 × 3 

7

/

8

 × 1 

1

/

2

 in.) 

 

(width / height / depth)

 

(including the audio input connector)

Mass

Approx. 139 g (4.9 oz) 

 

(excluding batteries)

Tuner (URX-P40/P41D)

Items common to all tuners

Antenna

1/4 

λ

 wavelength wire antenna (angle-

adjustable)

Audio output level variation range

–12 dB to +12 dB (3 dB steps)

Audio output connector

3.5-mm diameter 3-pole locking mini 

jack, Auxiliary connector

Headphone output level

10 mW max. (16-ohm)

Headphone output connector

3.5-mm diameter mini jack

Local oscillator Crystal-controlled PLL synthesizer
Receive frequencies

14UC model: 470.125 MHz to 

541.875 MHz 

 

(UHF-TV channels 14 to 25)

25UC model: 536.125 MHz to 

607.875 MHz 

 

(UHF-TV channels 25 to 36)

90U model: 941.625 MHz to 

951.875 MHz, 953.000 MHz to 
956.125 MHz, and 956.625 MHz to 
959.625 MHz

21CE model: 470.025 MHz to 

542.000 MHz 

 

(UHF-TV channels 21 to 29)

33CE model: 566.025 MHz to 

630.000 MHz 

 

(UHF-TV channels 33 to 40)

42CE model: 638.025 MHz to 

694.000 MHz 

 

(UHF-TV channels 42 to 48)

42LA model: 638.125 MHz to 

697.875 MHz 

 

(UHF-TV channels 42 to 51)

29CN model: 638.025 MHz to 

694.000 MHz 

 

(UHF-TV channels 29 to 35)

KR model: 925.125 MHz to 

937.375 MHz

E model: 794.125 MHz to 805.875 MHz

Signal-to-noise ratio

60 dB (1 kHz sine wave, 5 kHz 

modulation)

96 dB (1 kHz sine wave, max deviation)

Audio delay

Approx. 0.35 ms (analog output)
Approx. 0.24 ms (digital output)

Deemphasis

50 µs

Reference frequency deviation

±5 kHz

Frequency response

23 Hz to 18 kHz (Typical)

Distortion

0.9% or less (1 kHz sine wave, 5 kHz 

modulation)

Tone signal frequency

In UWP-D compander mode: 

32.382 kHz

In UWP compander mode: 32 kHz
In WL800 compander mode: 

32.768 kHz

Operating temperature

0 °C to 50 °C (32 °F to 122 °F)

Storage temperature

–20 °C to +55 °C (–4 °F to +131 °F)

When used in locations with an ambient temperature of 
45 °C (113 °F) or higher, make sure the unit does not 
come into direct contact with your skin, as it may cause 
burns due to high temperature.

USB port

USB Type-C

Supply voltage DC 3.0 V (two LR6/AA size alkaline 

batteries)

DC 5.0 V (supplied from USB 

connector)

Portable diversity tuner (URX-P40)

Audio output level

–60 dBV (3.5-mm diameter 3-pole 

locking mini jack, analog output, 
0 dB audio output level)

–20 dBFS (auxiliary connector, digital 

output, 0 dB audio output level)

–50 dBV (auxiliary connector, analog 

output, 0 dB audio output level)

Reception method

True diversity method

Indicators

POWER, RF

NFC function

Built-in

38 (1 

1

/

2

)

98 (3 

7

/

8

)

77 (1 

1

/

4

)

38 (1 

1

/

2

)

Note

Summary of Contents for URX-P40

























































Reviews: