39
OFF:
Select when not using an external microphone.
PLUG-IN PWR:
Select when using an plug-in power
type microphone.
MONO BMP+5V:
Select when using a Sony lavalier
microphone.
Adjusting the input level (INPUT LEVEL)
You can set the input level in the range –12 dB to +12 dB.
Adjust according to the microphone to be connected.
The factory default setting is 0 dB.
Setting the low-cut filter (LCF)
You can set the low-cut filter to reduce noise caused by
wind.
You can set the cutoff frequency to OFF/LOW/MID/
HIGH.
OFF:
No filtering
LOW:
100 Hz cutoff frequency
MID:
150 Hz cutoff frequency
HIGH:
200 Hz cutoff frequency
Switching the phase of the microphone
(PHASE)
You can switch the phase of a connected microphone to
output audio in reverse phase.
NORMAL:
Phase is not reversed.
INVERT:
Reverses the phase internally.
Selecting the connector for output of
input audio (OUTPUT ASSIGN)
Selects the connector for output of the input signal.
OUT1:
Output audio from the OUTPUT 1 connector. If
the connected microphone is a stereo (L/R) type, the
signals are mixed for output.
OUT1/2 (L/R):
Output audio from both the OUTPUT 1/
2 connectors. If the connected microphone is a stereo (L/
R) type, the L signal is output from OUTPUT 1 and the R
signal is output from OUTPUT 2.
OUT2:
Output audio from the OUTPUT 2 connector. If
the connected microphone is a stereo (L/R) type, the
signals are mixed for output.
The following combination of output connector settings
are supported.
Parentheses ( ) indicate the output for stereo (L/R) type
microphones.
Transmitter Settings
Menu structure and operation
Procedure for all transmitters (UTX-B40/M40/
P40)
There are three menu display modes that can be selected
according to the application.
Simple mode
This mode displays only the required settings for
transmitting audio.
You can enable simple mode by setting MENU MODE
(menu display mode) to SIMPLE.
Configuration menus
• GP/CH (group/channel) select
• BAND (frequency band) select (Not available on the
Japan model, Korea model, 90U model, and E model)
• ATTENUATOR (attenuator) setting
• GAIN MODE (audio gain) setting
• LCF (low-cut filter) setting
• INPUT LEVEL (audio input level) select (UTX-B40/
P40 only)
• RF POWER (RF transmit output level) select
• +48V SUPPLY (+48 V power supply) setting
(UTX-P40 only)
• POWER LOCK (POWER button lock) function
• RUNNING TIME (accumulated running time) display
• MENU MODE (menu display mode) setting
The following configuration menus cannot be modified
during transmission. Set these menus in transmission
stopped mode.
• GP/CH (group/channel) select
• BAND (frequency band) select (Not available on the
Japan model, Korea model, 90U model, and E model)
• RF POWER (RF transmit output level) select
Advanced mode
This mode displays all configuration menus.
You can enable advanced mode by setting MENU MODE
(menu display mode) to ADVANCED.
The existing settings configured in advanced mode are
active even when using simple mode.
Configuration menus
• GP/CH (group/channel) select
• BAND (frequency band) select (Not available on the
Japan model, Korea model, 90U model, and E model)
• ATTENUATOR (attenuator) setting
• GAIN MODE (audio gain) setting
• LCF (low-cut filter) setting
• INPUT LEVEL (audio input level) select (UTX-B40/
P40 only)
MIC INPUT
OUTPUT1
OUTPUT2
OUT1
OUT2
(L)
(R)
(L+R)
(L+R)
OUT1/2 (L/R)
Note
Note
Summary of Contents for URX-P40
Page 56: ...Sony Corporation ...
