Sony URX-P40 Operating Instructions Manual Download Page 38

Page: 38 / 56

Setting the frequency to an active channel
(ACT CH SCAN)

Searches for channels already in use. This is useful when
using more than one tuner in combination with a single
transmitter.

For details, see “Searching for active channels within a
group (Active Channel Scan)” (page 29).

Setting the compander mode
(COMPANDER)

The compander mode must be switched depending on the
transmitter to be combined with the unit.
You can set different compander modes for tuner 1 and
tuner 2.

• When operating in conjunction with UWP-D series

transmitters, set the compander mode of the transmitter
to the same setting as the unit (URX-P41D).

• No audio is output if the tone signal frequency is

different due to the use of a combination of devices with
different compander mode settings.

Press the MENU button to display the RX1 menu or
RX2 menu.

Press the + or – button to display the COMPANDER
screen.

Press and hold the SET button for one second or
longer.

The selected items starts flashing.

Press the + or – button to select the compander mode,
then press the SET button.

The selected compander mode is set.

UWP-D:

Select for combination with Sony UWP-D-

series transmitters.

UWP:

Select for combination with Sony UWP-series

transmitters.

WL800:

Select for combination with Sony WRT-

series transmitters.

Transmitter and compander mode
combinations

Configure the correct compander mode for the transmitter
you are using.

No audio will be output if the combination of transmitter
and compander mode setting is incorrect.

Selecting the connector for output of
received audio (OUTPUT ASSIGN)

Selects the connector for output of the received signal.
The factory default settings are OUT1 for tuner 1 and
OUT2 for tuner 2.

OUT1:

Output audio from the OUTPUT 1 connector.

OUT1/2:

Output audio from both the OUTPUT 1/2

connectors.

OUT2:

Output audio from the OUTPUT 2 connector.

The following combination of output connector settings
are supported.

EXT.IN menu

Procedure for portable diversity tuner
(URX-P41D)

The EXT.IN menu is used to configure settings for a
microphone connected to the MIC INPUT (audio input)
connector of the unit.

Selecting an external microphone to use
(MIC SELECT)

Selects the type of microphone connected to the MIC
INPUT (audio input) connector.

Notes

Note

Transmitter

Compander mode of
unit

UWP-D UWP

WL800

UWP-D series
(UTX-B40,
UTX-M40,
UTX-P40,

UTX-B03,

UTX-M03,
UTX-P03,
UTX-B03HR)

Compander
mode: UWP-D

Compander
mode: UWP

Compander
mode: WL800

Transmitter

Compander mode of
unit

UWP-D UWP

WL800

UWP series (UTX-B2, UTX-H2)

WRT series (WRT-822,

WRT-860, etc.)

Tuner 1

Tuner 2

OUTPUT1

OUTPUT2

RX1: OUT1

RX2: OUT2

RX1: OUT1/2

RX2: OUT1/2

RX1: OUT2

RX2: OUT1

Summary of Contents for URX-P40

























































Search results

Summary of Contents for URX-P40

Reviews:

Related manuals for URX-P40

Brands by name

Popular brands

Sony URX-P40, Operating Instructions Manual

Search results

Summary of Contents for URX-P40

Reviews:

Related manuals for URX-P40

Brands by name

Popular brands