Sony IT-M804 Operating Instructions Manual Download Page 64

Page: 64 / 80

Intercom Operation

Talking between the phones (Intercom) (continued)

Notes

• An intercom call is available between two phones only. If the other phone are

busy with intercom, page, or all page, you will hear a busy tone and “BUSY”
will be displayed.

• If the other phone is in Do Not Disturb mode, you will hear a short busy tone

and “DO NOT DISTURB” will be displayed.

• While conversing with an outside caller via the phone receiving an intercom

call, you cannot make an intercom call. If you press

(INTERCOM)

, you will

hear a busy tone.

• If you enter your station number mistakenly in step 3, you will hear five short

error beeps. If you enter a station number which has not been assigned, “NO
ANSWER” will be displayed.

Tips

• When you receive an intercom call, the phone will ring at a low level even

when the “RING VOLUME” is set to “OFF”.

• While on an intercom call, the INTERCOM lamp on the connected two

phones lights up and on other phones flashes.

• If you press

(INTERCOM)

in step 2 without performing step 1 on page 63, the

speakerphone will automatically turn on. When you’re done talking, press

(SPEAKERPHONE)

in this case.

• If you pick up the handset during speakerphone conversation, it will change

to handset conversation, and conversely when you press

(SPEAKERPHONE)

during handset conversation, it becomes speakerphone conversation.

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands