Sony IT-M804 Operating Instructions Manual Download Page 35

Page: 35 / 80

Basics

Basics

If you have subscribed to the Caller ID service including the caller name
service;

- the caller’s number and/or name appears on the display, and the date and

time are automatically set when you receive a call (see page 50).

- the ringer sound changes to a higher tone if the call matches the number

stored on one-touch dial button or in the Phone Directory (memory match
function; see page 50).

Notes

• When another phone connected to line is in use, the line button flashes

slowly.

• If a call is put on hold for more than about three minutes, you will hear an

alarm.

Using Do Not Disturb

You can turn off the outside call and intercom call ringing of all the
lines and voice from the speaker during a Page and an All Page using
this function. However, when a call comes in, “

RINGING

” will

be displayed even if this function is activated.

Making calls is available even if this function is activated.

While the phone is not in use or the phone is ringing, you can press

(DO NOT DISTURB)

The DO NOT DISTURB lamp lights up.

To cancel this function, press

(DO NOT DISTURB)

again.

Note

An outside call cannot be transferred to the phone with the “DO NOT
DISTURB” function activated.

continued

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands