Sony IT-M804 Operating Instructions Manual Download Page 30 | Manualshive

Page: 30 / 80

background image

Basics

30

US

Making calls (continued)

Notes

• When another extension connected to line is in use, the line button flashes.
• When another call comes in on the other line, the corresponding line button

flashes and two beeps are heard from the speaker, but the phone won’t ring.
(see page 36).

• If a call is put on hold for more than about three minutes, you will hear an

alarm.

Tips

• You can switch to speakerphone during conversation by pressing

(SPEAKERPHONE)

. Then you can replace the handset in the cradle.

To switch back to the handset, pick up the handset again.

• When you pick up the handset or press

(SPEAKERPHONE)

, the vacant line is

automatically connected from line 1 to line 4. When neither line is in use, line
1 is connected.

To obtain the best speakerphone performance

• You may not be able to hear the other party’s voice in a noisy place.

Therefore, use the speakerphone in a quiet room.

• Do not bring your hand or other objects too close to the microphone

or you will hear a shrill noise (“feedback”).

• When the speaker volume is loud, or the telephone has been placed

close to a wall, you may find that the volume drops suddenly. This is
due to a circuit in the telephone designed to protect against
feedback. In such cases, lower the speaker volume slightly.

«
...
28
29
30
31
32
...
»

Summary of Contents for IT-M804

















































































Reviews:

No comments

Related manuals for IT-M804

Brand: D-Link Pages: 2

T-Octophon F 50

Brand: T-COM Pages: 167

Brand: BT Pages: 2

Brand: Verizon Pages: 55

Brand: Topcom Pages: 33

XDECT 8315 Series

Brand: Uniden Pages: 44

Brand: AT&T Pages: 31

Brand: Uniden Pages: 16

Brand: Premier Pages: 12

Brand: GAI-Tronics Pages: 20

Brand: Depaepe Telecom Pages: 2

Brand: AT&T Pages: 15

Brand: BT Pages: 80

Brand: CDK Global Pages: 6

Brand: Curtis Pages: 6

Brand: AEG Pages: 176

Brand: AEG Pages: 48

Voxtel D555 twin

Brand: AEG Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands