Sony IT-M804 Operating Instructions Manual Download

Page: 17 / 80

Getting Started

Getting Started

Choose the dialing mode

For the telephone to work properly, select an appropriate dialing
mode (tone or pulse).

When other phones (IT-M804 or IT-M704) are connected to the LINE 1
jack, the same dialing mode is automatically set to all the phones. Be
sure to connect the phones beforehand, and set the dialing mode.

Press

(PROGRAM)

Turn Jog Dial up until “DIAL
MODE” appears on the display.

Press Jog Button.

Turn Jog Dial to choose the
dialing mode (“TONE” or
“PULSE”), and then press Jog
Button.

You will hear a long
confirmation beep.

Notes

• Do not allow more than 20 seconds to elapse between each step of the

procedure.

• The dialing mode cannot be set for every line.

Tip

You can press

(PROGRAM)

instead of Jog Button in the procedure above.

If you aren’t sure of your dialing system

Make a trial call with the dialing mode set to “TONE”.
If the call connects, leave the setting as is; otherwise, set to “PULSE”.

TONE PULSE

continued

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands