Sony IT-M804 Operating Instructions Manual Download Page 54

Page: 54 / 80

Caller ID Features

Looking at the Caller ID list (continued)

To erase the entire list at once

Display “END OF LIST” by
turning Jog Dial.

Press

(ERASE/CLEAR)

“ERASE ALL?” is displayed,
and “YES NO” appears after
about two seconds.

Turn Jog Dial to choose “YES”,
and then press Jog Button.

You will hear a long
confirmation beep and the
entire list is erased.

Notes

• If you intend to erase the entire list with any new calls remaining, you will

hear five short error beeps and you cannot erase the list.

• The “saved” numbers (see page 52) are not erased even if you erase the entire

list. To erase the “saved” numbers in the Caller ID list, follow the procedure
in “To erase phone numbers one by one”.

END OF LIST

ERASE ALL ?

Jog Button

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands