Sony IT-M804 Operating Instructions Manual Download Page 23

Page: 23 / 80

Getting Started

Getting Started

Press Jog Button.

Enter the two digits for the hour (01 to 12) by
pressing the dialing keys.

The hour is on a 12-hour cycle.

Press Jog Button.

Enter the two digits for the minute (00 to 59)
by pressing the dialing keys.

Press Jog Button.

Turn Jog Dial to choose “AM” or “PM”, and
then press Jog Button.

You will hear a long confirmation beep.

Notes

• Do not allow more than 20 seconds to elapse between each step of the

procedure in steps 1 to 11 and 60 seconds in step 12.

• The time is renewed each time the phone receives the Caller ID.

Since the Caller ID sends time information by the unit of one minute, the time
indication may be one minute behind at most.

Tip

You can press

(PROGRAM)

instead of Jog Button in the procedure above.

HOUR=01

MINUTE=01

AM PM

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands