Sony GV-D200E, Service Manual, Page: 101 / 166

5-11
3-2. INITIALIZATION OF C, D, E, F, 7, 8 PAGE
DATA
3-2-1. INITIALIZATION OF C, D, 8 PAGE DATA
1. Initializing the C, D, 8 Page Data
Note 1: If “Initializing the C, D, 8 Page Data” is performed, all data of the
C page, D page and 8 page will be initialized. (It is impossible to
initialize a single page.)
Note 2: If the C, D, 8 page data has been initialized, the following
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Servo and RF system adjustments
4) Video system adjustments
5) LCD system adjustments
6) Battery end adjustments
Adjusting page C
Adjusting Address 10 to FF
Adjusting page D
Adjusting Address 10 to FF
Adjusting page 8
Adjusting Address 00 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data
2 3 81 10 Set the data
3 3 80 0A Set the data, and press the
PAUSE button.
4 3 80 Check that the data changes to
“1A”
5 Perform “Modification of C, D,
8 Page Data”.
2. Modification of C, D, 8 Page Data
If the C, D, 8 page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of C, D, 8 Page data
Order Page Address Data Procedure
1 2 00 29 Set the data
2 2 01 29 Set the data, and press the
PAUSE button.
Note: If the following symptoms occur after completing of the
“Modification of C, D, 8 page data”, check that the data of the “Fixed
data-2” addresses of D page are same as those of the same model of
the same destination.
1) The battery end mark on the LCD screen is flashing.
2) The power is shut off so that unit cannot operate.
3. C Page Table
Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8
Page Data”).
Address Remark
Initial value
NTSC PAL
00 to 0F
10
11
12
13
14 to 16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23 to 24
25
26
27
28
29
2A to 2B
2C
2D to 2E
2F
30
31 to 45
46
47 to 4C
4D
4E to 85
86
87 to 88
89
8A to 91
92
EE
00
00
00
E0
25
25
25
25
25
3E
3E
CA
99
88
E3
A1
04
20
03
E0
EE
00
00
00
E0
25
25
25
25
25
3E
3E
CA
99
88
E3
A1
04
20
03
E0
Switching position adj.
Fixed data-1
REEL FG adj.
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL fo adj.
APC adj.
LPF fo adj.
Fixed data-1
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF fo adj.
PLL fo fine adj.
Fixed data-1
APC adj.
Fixed data-1
Fixed data-2
REEL FG adj.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2