![background image](http://html.mh-extra.com/html/sony/cmt-se7/cmt-se7_operating-instructions-manual_420449086.webp)
masterpage:Left
filename[\\Nas-data-server\SONY Current jobs\SONY CMT-SE7\CMT-
SE7_GBCT\DTP\4248325112\424832511CMTSE7HK\GB13TRB-CEK.fm]
86
GB
model name [CMT-SE7]
[4-248-325-11(2)]
MD deck
An MD cannot be inserted.
• Insert the MD with the label side up and the arrow
pointing toward the deck.
The controls do not work.
• Replace the MD with a new one.
• Retry the operations after “TOC” turns off.
• If M-crew is active or present in the task tray at the
bottom right of the screen, quit M-crew and then
perform the operation.
Play does not start.
• Replace the MD.
• Insert the MD and leave the system turned on for
a few hours until the moisture evaporates.
• Press MD
N
to start play.
• Press MD GROUP until “GROUP ON”
disappears to cancel the Group Function.
The sound skips.
• Replace the MD.
• Try moving the system to a place without
vibration (e.g., on top of a stable stand).
• Try moving the speakers away from the system, or
placing them on separate stands. When you listen
to a track with bass sounds at high volume, the
speaker vibration may cause the sound to skip.
• Insert the disc and wait for 10 to 20 minutes with
the system turned on.
Play does not start from the first track.
• Press PLAY MODE repeatedly until both “PGM”
and “SHUF” disappear to return to Normal Play.
“OVER” appears.
• You have reached the end of the MD. Press and
hold
m
or press
.
to return to the desired
playing position.
“OVER” lights up during recording.
• Adjust the recording level lower (page 46).
Recording or editing was done, but the TOC is
not updated.
• MD recording and editing contents are recorded to
the MD when the MD is removed, so make sure
you remove the MD after recording or editing
(pages 38 and 48).
The track is not deleted.
• Perform Check-In the track with SonicStage for
Sony Net MDs and delete the track (page 78).
Recording is not possible.
• Remove the MD and slide the tab to close the slot
• Connect the optional component properly
• Press FUNCTION repeatedly to select the
recording source correctly.
• Replace with a recordable MD.
• Replace the MD with a recordable MD, or use the
Erase Function to erase unnecessary tracks
(page 54).
• Start recording again.
• Only the CD layer of Super Audio CDs can be
recorded.
Synchro recording is not possible.
• You cannot use the Synchro recording function
with DVDs.
The sound from an MD you recorded is too low
(or too high).
• Adjust the recording level (page 46).
High-speed CD-MD synchro recording is not
possible and the system swithes to normal-
speed recording.
• High-speed CD-MD synchro recording is not
available for discs other than CDs or the CD layer
of Super Audio CD.
• Replace the disc.
• Change the installation position of the unit.
Sound leaks when recording in LP4 stereo
mode.
• Record in stereo or LP2 stereo mode. When
recording the sound from a CD, tape or optional
component with music or audio on only one
channel in LP4 stereo mode, the sound may leak
to the empty channel.
Track numbers are not marked on recorded
MDs.
• You are recording sound with a lot of noise.
Adjust so that track numbers are marked correctly.
Tuner
Severe hum or noise/stations cannot be
received. (“TUNED” or “STEREO” flashes in
the display.)
• Set the proper band and frequency (page 62).
• Connect the antenna properly (page 8).
• Set “DVD POWER OFF” by DVD power manage
function (page 63).
• Find a place and an orientation that provide good
reception, then set up the antenna again. If you
cannot obtain good reception, we recommend you
connect a commercially available external
antenna.