Sonnen sonnenBatterie ecoLinx 10 Installation And Operating Manual Download Page 10

 

2

Safety 

Intended use 

Any use of the system other than the intended 

use can cause serious injury, death, and damage to 

the product or other assets.
•  The storage system must only be used to store 

electrical power.

•  The storage system must only be used with the 

battery modules provided.

•  The storage system is intended for indoor use 

only.

•  The intended use includes knowledge 

and application of the information in this 

installation and operating manual as well as all 

delivered product documentation.

Failure to comply with the warranty 

conditions and the information listed in 

this installation and operating manual 

will void any warranty claims.

Prohibited uses

DANGER

Danger to life due to electric 

shock! 

Even if the utility grid fails, the 

storage system will continue 

delivering power. Before servicing 

the storage system:

 

Turn off the storage system.

 

Turn off the main disconnect 

circuit breaker.

Only authorized electrically 

qualified persons can perform work 

on electrical parts.

•  Do not use the storage system in vehicles.
•  Do not use the storage system in wet locations.
•  Do not use the storage system in areas at risk 

of explosion (flour dust, sawdust, etc.).

•  Do not expose the storage system to direct 

sunlight.

•  Do not use the storage system in areas where 

the ammonia content of the air exceeds 20 

ppm.

•  Do not use the storage system when corrosive 

gases are present.

•  Do not use the storage system higher than 

9,842 feet (3,000 meters) above sea-level.

•  Do not operate the storage system at 

temperatures outside of the allowed ambient 

temperature range of 41°F - 113°F (5°C - 45°C).

•  Do not operate the storage system at a 

humidity higher than 90%.

General warnings 

Attention

Attention
Damaging of the battery modules by deep 

discharge! 

If the battery modules are disconnected from a 

power source for longer than six months, they can 

be damaged by excessive discharge.

 

If the storage system has been disconnected 

from the utility grid for six months, connect 

it to the utility grid and allow it to charge the 

battery modules to 100%.

General safety instructions

•  Do not modify the storage system.
•  Do not use the storage system if it has been 

damaged.

•  Ensure the following regulations are observed 

in the installation and connection of the 

storage system and the PV system:

 

Local, regional, national, and international 

regulations and guidelines

 

National Electric Code 

 

ANSI/NFPA 70

 

Requirements of the servicing utility

•  Ensure that all safety systems are in perfect 

working order.

•  Read this installation and operating manual 

with care.

Summary of Contents for sonnenBatterie ecoLinx 10

































































Reviews: