Somogyi Home FK360/BK Instruction Manual Download Page 4

Page: 4 / 20

TROUBLESHOOTING

5. If it is used wall mounted, mount the unit without bases on the wall, using the enclosed fittings. (

Fig. 4

)

a. Remove the wall consoles from the back of the unit after loosening the two safety screws.

b. Fasten the wall console with wall studs and 4 screws to the wall. Use studs conforming to the size of

the screws and structure of the wall. Make sure the wall console stays horizontally on the wall.

c. Hang the 2 hangers located at the bottom of the back side of the unit onto the screws, then tilt

towards the wall hook the two upper fixing point as well.

d. Tighten the safety screws.

6. To ensure proper operation, free circulation of hot air must be ensured. Therefore, please, observe the

minimum installation distances indicated in

Figure 2

7. The switches on the unit must be in OFF position!

8. Insert 1 pc CR2025 (3 V) button battery to the remote controller. Pay attention to the correct polarity!

9. Connect the unit into a standard grounded wall power socket! Now the unit is ready for operation!

Caution: Risk of electric shock!

Do not attempt to disassemble of modify the unit or its

accessories. In case any part is damaged, immediately power off the unit and seek the assistance of

a specialist.
In the event that the power cable should become damaged, it should only be replaced by the

manufacturer, its service facility or similarly qualified personnel.
Meaning of symbol on appliance:

Do not cover!

Covering the unit can cause overheating, fire or electric shock!

FEATURES

electric heater for heating the atmosphere of indoor premises • with touch buttons • with
remote controller • adjustable output 1000 W / 2000 W • electronic thermostat • weekly
program • child safety lock • IPX4: protected from splashing water • tempered glass front
panel • wall-mountable or standalone design • automatic switch-off when overheating

STRUCTURE (Figure 1.)

main switch •

removable base (included) •

screws for fixing the base •

wall console •

safety screws •

screws, studs •

power cable •

tempered glass front panel

Display:
9.

display •

10.

heating stage selection •

11.

selection keys •

12.

„MIN” button •

13.

„MODE”

button •

14.

„SET” button

Remote controller:
15.

„SET” button •

16.

„MODE” button •

17.

child safety lock •

18.

heating stage selection •

19.

selection keys

OPERATION

After you have connected the appliance to the power network, switch it on with the main
switch. It will emit a short beep.

Standby mode

When the main switch is turned on, the device is in standby mode, then it does not heat up.
The display shows the day, time, and mark.
To set the time: To set the clock, press and hold [MODE] button, to set the minute, press and
hold [MIN] button, to set the days of the week press and hold [SET] button.

Heating

Press the [SET] button to switch the unit to heating mode. The appears on the display.
To set the heating stage / , press button. The desired temperature can be set by
pressing and or using the and buttons on the remote controller, from 5 to 40 ° C.
The current (left) and the set (right) temperature can be read side by side.

Weekly program

Press the [SET] button to switch the unit to timer mode. The appears on the display.
Press the [MODE] button to select the desired days or combinations of days. The days can
be combined as follows:

MON – TUE – WED – THU – FRI
MON – TUE – WED – THU – FRI – SAT
MON – TUE – WED – THU – FRI – SAT – SUN
MON – WED – FRI
TUE – THU – SAT
SAT – SUN
MON – TUE – WED
THU – FRI – SAT
MON, or TUE, or WED, or THU, or FRI, or SAT, or SUN

By pressing the button you can select the desired heating stage.
Press the button to enter the ON TIME, press the button to enter the time off. During
programming, each hour of the day must be set for the device to heat or not.

Example: Set

the appliance to do not heat from midnight to 8 o'clock on a given day / days, heat from 8 to 14
o'clock, then do not heat from 14 o'clock until midnight.

Setting: Display shows 00:00. Press

the button 7 times, the display will show 07:00. Then press the button six times, 13:00
will visible on the display. Then press the button 11 times. The display shows the exact
time.

Child safety lock

You can activate or deactivate the child lock by pressing the

button for 3 seconds on the

unit or pressing the

button on the remote control.

Operation

If the room temperature reaches the set temperature, the high cooling stage will be
deactivated and the appliance will be heated at a low temperature. If the room temperature
exceeds the set temperature by 2 °C, the appliance will not heat more. The appliance
switches on again when the room temperature falls 2 °C below the set value.

In the event of overheating, the

overheating protection function

will switch off the unit, for

example when the air inlets and outlets are covered. Power off the unit by unplugging it from
the electric outlet. Allow the appliance to cool (for at least 30 minutes). Check whether the air
inlets and outlets are obstructed or not, and clean them if necessary. Install the unit again. If
the overheating protection activates again, power off the unit by unplugging it from the electric
outlet and contact the service facility.

CLEANING AND MAINTANCE

In order to ensure optimum functioning, the unit may require cleaning at least once a month,
depending on the manner of use and degree of contamination.
1. Switch off and power off the unit by unplugging it from the electric outlet before cleaning.
2. Allow the appliance to cool (for at least 30 minutes).
3. Clean the protective grill using a vacuum cleaner equipped with a brush accessory.
4. Use a slightly moistened cloth to clean the unit’s outer surface. Do not use any aggressive

cleaners. Avoid getting water inside of and on the electric components of the appliance!

SUN

MON

TUE

WED

THU

FRI

SAT

Sunday

Monday

Tuesday

Wednesday