Caution: Risk of electric shock!
Do not attempt to disassemble or modify the unit or its
accessories. In case any part is damaged, immediately power off the unit and seek the assistance of
a specialist
.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
Meaning of symbol on appliance:
Do not cover!
Covering the unit can cause overheating, fire or electric shock!
FEATURES
panoramic decorative fireplace with built-in fan-assisted heater for heating the atmosphere of indoor premises • attractive flame effects • adjustable brightness • switchable air blower and heating •
heat output control 900 / 1800 W • thermostat control • overheating protection
ASSEMBLY
(
Figure 1
)
1.
cold air inlets
•
2.
heated air outlet grille
•
3.
light compartment cover plate
•
4.
power cable
•
5.
access lid
•
6.
flame effect switch
•
7.
heating stage I (900 W)
•
8.
heating stage II (+900 W)
•
9.
fan
switch
•
10.
flame effect brightness controller
•
11.
temperature setting button
SETUP
1. Before switching on for the first time, carefully remove the packaging material taking care not to damage the appliance and power cable. Do not use the product if it is damaged in any way.
2. The unit may only be used indoors in dry conditions.
3. Set the appliance on a stable and horizontal surface. The free flow of warm air must be ensured for proper operation, therefore, please note the minimum installation distances indicated in
Figure 2.
Make sure that no foreign objects cover the cold air inlets on the rear of the appliance.
4. Do not locate the appliance directly below a wall outlet. Verify that the unit’s mains switch (5) is in the OFF “0” position.
5. Verify that the unit’s switches are in the OFF position.
6. Plug the unit’s standard grounded AC power cable into a grounded wall outlet. This completes the setup of the appliance.
OPERATION
The appliance can be operated using the controls located under the top cover.
The unit may emit a slight odor when turned on initially, which is not a malfunction. It is harmless and wears off quickly.
button can be used to turn the flame effect on or off.
the brightness control button can be used to adjust the brightness of the flame effect.
the fan switch can be used to switch the fan-only function on or off.
The two 900 W switches can be used to select a heating output of 900 W or up to 1800 W. Until the preset temperature is reached, the
thermostat
switches on the heating elements previously
activated and switches them off when the temperature is reached while the fan continues to operate. The thermostat clicks at the current temperature when its knob is turned. Turn clockwise to set
a higher temperature.
In the event of overheating, the
overheating protection function
will switch off the unit, for example, when the air inlets and outlets are covered. Power off the unit by unplugging it from the electric
outlet. Allow the appliance to cool (for at least 30 minutes). Check whether the air inlets and outlets are obstructed or not, and clean them if necessary. Switch on the unit again. If the overheating
protection activates again, power off the unit by unplugging it from the electric outlet and contact the service facility.
BULB REPLACEMENT
Warning! Power off the unit by unplugging it from the electric outlet prior to replacing bulbs.
Allow the appliance to cool (for at least 30 minutes). The appliance contains two 25 W (230 V~ / 50 Hz) conventional chandelier bulbs with E14 sockets. To replace the bulbs remove the two screws
that fasten the bulb compartment cover on the rear of the appliance then lift the cover off. CAUTION! Sharp edges! Now you can replace the two light bulbs of the same kind and rating (Max. 25 W).
Do not use compact fluorescent or LED light sources. Replace the cover after changing the bulbs. The bulbs are not covered by the warranty.
CLEANING & MAINTENANCE
In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of contamination.
1. Switch off and power off the unit by unplugging it from the electric outlet prior to cleaning.
2. Allow the appliance to cool (for at least 30 minutes).
3. Use a vacuum cleaner to clean the air inlet (1) and outlet (2) openings.
4. Use a slightly moistened cloth to clean the unit’s exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric components of the appliance.
TROUBLESHOOTING
DISPOSAL
Waste equipment must not be collected separately or disposed of with household waste because it may contain components hazardous to the environment or health. Used or
waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility
specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the
local waste management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and shall bear any associated costs
arising.
SPECIFICATIONS
power supply:. . . . . . . . . . 230 V / 50 Hz
heating power ( ): . . . 900 / 1800 W
bulbs ( ): . . . . . . . . . . . . 2 x max. 25 W (230 V~ / 50 Hz / E14)
max. power: . . . . . . . . . . . 1850 W
IP protection: . . . . . . . . . . IP20: Not protected from ingress of water!
size of heater: . . . . . . . . . 59,5 x 64 x 29 cm
weight: . . . . . . . . . . . . . . . 17,5 kg
length of power cable: . . . 1,6 m
sound pressure: . . . . . . . . 48 dB(A)
Solution
Check the power supply.
Check the power supply.
Check the settings of the thermostat.
Check the instructions described at overheating.
Check the power supply.
Check the light bulbs.
Clean the appliance.
Cause
The ventilator is not working.
The appliance does not heat.
Flame effect does not work.
The overheating protection activates frequently.