Caution: Risk of electric shock!
Do not attempt to disassemble or modify the unit or its
accessories. In case any part is damaged, immediately power off the unit and seek the assistance of
a specialist
.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
Meaning of symbol on appliance:
Do not cover!
Covering the unit can cause overheating, fire or electric shock!
FEATURES
halogen heater for heating the atmosphere of indoor premises • 400 / 800 / 1200 W output • immediate heat radiation • switchable oscillation • overheating protection • tip-over protection • recessed
carrying handle • replaceable heating elements
STRUCTUE (Figure 1.)
1.
radiating surface with protective grill •
2.
replaceable heating elements •
3.
operation mode switch •
4.
recessed carrying handle •
5.
base •
6.
base fastening screws •
7.
tip-over protection switch
•
8.
cable holder •
9.
power cable
SETUP
1. Before switching on for the first time, carefully remove the packaging material taking care not to damage the appliance and power cable. Do not use the product if it is damaged in any way!
2. The base has to be assembled to the appliance.
a. Unscrew the 2 base-fixing screws from the bottom of the appliance.
b. Unwind the power cable completely, and lead it through the centre of the base. Put the base part to the bottom of the unit. The cable holder (8) should face the rear of the appliance.
c. Fasten the base using the two screws.
d. Fasten the power cable using the cable holder.
3. Set the appliance on a stable and horizontal surface. Do not place on flammable materials such as wood, carpet, etc. The unit should only be placed on non-flammable materials such as stone,
marble or floor tiles.
4. The free flow of warm air must be ensured for proper operation, therefore, please note the minimum installation distances indicated in
Figure 2.
Do not locate the appliance directly below or next
to a wall outlet!
5. The operating mode switch of the appliance (3) must be set in turned off „0” position!
6. Plug the unit’s standard grounded AC power cable into a grounded wall outlet. Now the unit is ready for operation!
OPERATION
Appliance can be controlled by turning the operating mode switch (3). „0” indicates the turned off status. Turning it to one direction you can select 400 W / 800 W / 1200 W heating levels, and
turning to the other direction, the same options are selectable together with oscillation. The heating elements are 400W each so the maximum switchable output is 1200W. The unit may emit a
slight odor when turned on first time, which is not a malfunction. It is harmless and evaporates quickly.
A switch on the bottom of the appliance turns it off, if it should topple over. In such cases remove power from the appliance by pulling out the power plug then stand the appliance upright and
reinstall it only afterwards according to the section entitled SETUP.
REPLACEMENT OF HEATING ELEMENT
Warning: The heating element should only be replaced by a specialist!
Power off the unit by unplugging it from the electric outlet prior to replacement. Heating element type: FK 23/T
(163 mm, 400 W).
The appliance may not be operated without the protective grill on its place!
The heating element operates much like a conventional incandescent light bulb. Burnt out heating elements are not covered by the warranty as they are subject to natural wear.
CLEANING & MAINTENANCE
In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of contamination.
1. Switch off and power off the unit by unplugging it from the electric outlet before cleaning.
2. Allow the appliance to cool (for at least 30 minutes).
3. Use a vacuum cleaner to clean the protective grille. The heat reflector does not require cleaning.
4. Use a slightly moistened cloth to clean the unit’s exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric components of the appliance!
TROUBLESHOOTING
Waste equipment must not be collected separately or disposed of with household waste because it may contain components hazardous to the environment or health. Used or waste
equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in
the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste
management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and shall bear any associated costs arising.
SPECIFICATIONS
power supply:....................230 V~ / 50 Hz
rated power: ......................400 / 800 /1200 W
max. output: ......................1200 W
heating element type: ........FK 23/T (163 mm, 400 W)
IP protection: .....................IP20: Not protected from ingress of water!
size of heater:....................30 x 70 x 30 cm
weight: ..............................1,9 kg
length of power cable:........1,25 m
Solution
Check the power supply.
Check the tip-over protection switch.
Check the position of the switches.
The heating element might have burned out. Contact a specialist!
Cause
The unit does not heat in heating mode.
