background image

13

English

12

Preparing and drilling gateposts 

1

Preparing and drilling gateposts 

1

Carry dimension B over and trace a
vertical baseline (AM) onto the
gateposts.

Steps:

Dimension measurement.

The type of gate determines where the motors are to be placed. 
Measure the dimensions described below to determine their position on the gateposts:
For these measurements, the leaves and their hinges are supposed to be on the same
axis. If the hinges are not aligned (offset), the leaves' maximum opening angle will be
less than the values shown.

Take care to follow the recom-
mendations in the instructions

provided with the chemical sealants
when determining the drilling method
and diameters.

Drilling the gateposts.

Marking the AM and AH baselines.

Dimension measurement.

Marking the AM and AH baselines.

Drilling the gateposts.

Measure dimension A

Using the table below, determine:
• the  maximum opening value of the

leaves,

• dimension  to determine the vertical

positioning axis of the motors on the
gateposts.

D

Dimension A (mm) 

Maximum opening  (°) 

Dimension B (mm)

0

120 205

0

110

160

0

105 150

50

100

150

100

95

150

150, 

250

90

150

1

Using a small-diameter (4 or 5 mm)
concrete drill bit, pre-drill 4 holes for
filling with chemical sealants into each
gatepost, in the positions marked on the
template.
Finish drilling the 4 holes using a
concrete drill bit whose diameter
corresponds to the chemical sealants.

2

Trace the horizontal line (AH) onto the
post, halfway up the bracket.

2

100

Position the template at the intersection
of baselines AM and AH.

1

Self-check before the next step

Have you properly aligned the AM and AH baselines on the
template and gatepost?

Check dimensions D and

L

For safety's sake, check:
• dimension  D, , which must be

greater than or equal to 405
mm,

• dimension L, which must be

between 800 and  2,000 mm.

SGA6000 gb.qxd  12/02/08  17:54  Page 12

Summary of Contents for SGA 5000






















Reviews: