background image

3

 - be fitted with a lightning conductor (in compliance with standard NF C 61740, maximum residual voltage 2 kV),

 Check whether the earthing system is installed correctly: connect all the metal parts of the assembly and all the components of the installation equipped 

with earth terminals.
 After installation, ensure that the mechanism is correctly adjusted and that the protection system and any manual release mechanism operate correctly.

Safety devices

 The selected safety accessories for the installation must comply with the current standards and regulations in force in the country in which the product is 

being installed. The use of any safety components not approved by Somfy remains the sole responsibility of the installer.
 Install all the safety devices (photoelectric cells, safety edges, etc.) required to protect the zone from the danger of crushing, entanglement and cutting 

according to the applicable directives and technical standards.
 In accordance with standard EN 12453 governing the safe use of motorised gates and doors, the use of the TAHOMA control box to automatically control a 

garage door or gate not visible to the user requires the installation of a photoelectric cell type safety device with autotest on the automatic control system.

maintenance

 Regularly check the condition of the gate. Gates in poor condition must be repaired, reinforced or even replaced. Check that the various motorisation 

component's screws and fittings are correctly tightened.

Before carrying out work on the installation, switch off the power supply.
Use only original parts for any maintenance or repair work. 

PrOduCT dESCrIPTION

 Size of motor (in mm)

166.12

175

938.83

309.

9

245

30.

5

297.

5

Technical data

Power supply

230 V - 50/60 Hz

Standby power consumption (excluding accessories)

2.6 W

Standby solar power consumption

1 W

Max. power consumption

600 W

Average frequency of movements per day

20 cycles/day

Max. thrust force at 1.25 m

< 15 kg EN 12453

Operating temperature

-20°C to +60°C

Thermal protection

Yes

Index protection rating

IP 44

Integrated radio receiver

Yes

Number of storable remote controls

16

Motor feed outputs

24 V DC

Power per motor

120 W

Output for orange light

Flashing, 24 V, 15 W

Area lighting output

500 W max.

Accessories supply output

24 V CC/1 A (including orange light)

Backup battery input

Yes

Photoelectric cell input

Yes (1 or 2 sets)

Dry contact input 

Yes

Summary of Contents for HOME MOTION Axovia 220B



























Reviews: