background image

5.5 Connection of the Inverter

PV String Connection

Ø

X3-PRO G2 series inverter have three couples of PV connectors which can be 
connected in series into 3-strings PV modules. Please select photovoltaic 
modules with good performance and quality assurance. The open circuit voltage 
of the module array should be less than the maximum PV input voltage specified 
by the inverter, and the operating voltage should be within the MPPT voltage 
range.

Table 3   Max. DC Voltage Limitation

Max. DC Voltage

1100 V

Warning!

The voltage of PV modules is very high and dangerous , please 
comply with the electric safety rules when connecting.

Warning!

Do not ground the positive or negative pole of the
photovoltaic module!

Note!

Please follow the requirements of PV modules as below:
Same type; Same quantity; Identical alignment; Identical tilt.
In order to save cable and reduce the DC loss, we suggest 
installing the inverter near PV modules.

5.5.1  The Main Steps to Connect to the Inverter

IBMU

Installation 

Installation 

Model

Danger!

Danger to life due to high voltage on DC conductors.
when exposed to sunlight, the PV array generates dangerous DC 
voltage which is present in the DC conductors. Touching the DC 
conductors can lead to lethal electric shocks.
Do not cover the PV modules. Do not touch the DC conductors.

Connection Steps

X3-PRO-8K-G2(2D) 

X3-PRO-10K-G2(2D)

X3-PRO-15K-G2

 

(2D) 

X3-PRO-12K-G2(2D) 

X3-PRO-25K-G2(3D) 

24

25

X3-PRO-30K-G2(3D) 

Step 1. Turn off the DC switch, connect the PV module, prepare a 2.5-4 mm  PV  
cable, and find the PV (+) terminals and PV (-) terminals in the package.

PV cable

PV pin 

contacts

Negative terminal

s

Positive terminal

s

Step 2. Use a wire stripper to strip 7 mm insulation layer from the wire end.

7.0 

mm

Wire stripper

Step 3. Tighten the cable with the insulation layer stripped and insert it into 
the pin contact (see Figure 1), make sure all wires are inserted into the pin 
contact (see Figure 2).

Figure 1

Figure 2

Positive PV 
pin 

contact

Negative PV 
pin 

contact

 

X3-PRO-17K-G2(2D) 

X3-PRO-20K-G2(3D) 

X3-PRO-17K-G2(3D) 

X3-PRO-20K-G2(2D) 

X3-PRO-15K-G2

 

(3D) 

Summary of Contents for X3-PRO G2 Series


































Reviews: