Sofarsolar SOFAR 1100TL Installation And Operating Manual Download Page 76

Page: 76 / 82

TROUBLESHOOTING HANDLING

SOFAR 1100...3300TL-G3

Name

Description

Solution

UnrecoverHw

AcOCP

The grid current is too

high and has caused an

unrectifiable hardware

error

ID65-ID70 are internal inverter

errors, switch the DC switch OFF,

wait 5 minutes and then switch the

DC switch ON. Check whether the

error has been rectified. If not,

please contact the technical

support department.

UnrecoverBu

sOVP

The bus voltage is too high

and has caused an

unrectifiable error

UnrecoverIac

RmsUnbalan

The grid current is

unsymmetrical and has

caused an unrectifiable

error

UnrecoverIpv

Unbalance

The input current is

unsymmetrical and has

caused an unrectifiable

error

UnrecoverVb

usUnbalance

The bus voltage is

unsymmetrical and has

caused an unrectifiable

error

UnrecoverOC

PInstant

The grid current is too

high and has caused an

unrectifiable error

UnrecoverPv

ConfigSetWr

ong

Incorrect input mode

Check the setting of the MPPT

input mode (parallel

mode/independent mode) of the

inverter and correct if required.

Summary of Contents for SOFAR 1100TL



















































































Search results

Summary of Contents for SOFAR 1100TL

Reviews:

Related manuals for SOFAR 1100TL

Brands by name

Popular brands

Sofarsolar SOFAR 1100TL, Installation And Operating Manual

Search results

Summary of Contents for SOFAR 1100TL

Reviews:

Related manuals for SOFAR 1100TL

Brands by name

Popular brands