Sofarsolar SOFAR 1100TL Installation And Operating Manual Download Page 79

Page: 79 / 82

TROUBLESHOOTING HANDLING

SOFAR 1100...3300TL-G3

Name

Description

Solution

SDfault

The SD card is defective

Please replace the SD card.

8.2

Maintenance

Inverters do not generally require daily or routine maintenance. Before

carrying out cleaning, ensure that the DC switch and AC circuit breaker

between the inverter and power grid have been switched off. Wait at least

5 minutes before carrying out cleaning.

8.2.1

Cleaning the inverter

Clean the inverter using an air blower and a dry, soft cloth or a soft bristle

brush. Do NOT clean the inverter with water, corrosive chemicals,

cleaning agents etc.

8.2.2

Cleaning the heat sink

In order to help guarantee correct long-term operation of the inverter,

make sure that there is sufficient space for ventilation around the heat

sink. Check the heat sink for blockages (dust, snow etc.) and remove them

if present. Please clean the heat sink using an air blower and a dry, soft

cloth or a soft bristle brush. Do NOT clean the heat sink with water,

corrosive chemicals, cleaning agents etc.

Summary of Contents for SOFAR 1100TL



















































































Search results

Summary of Contents for SOFAR 1100TL

Reviews:

Related manuals for SOFAR 1100TL

Brands by name

Popular brands

Sofarsolar SOFAR 1100TL, Installation And Operating Manual

Search results

Summary of Contents for SOFAR 1100TL

Reviews:

Related manuals for SOFAR 1100TL

Brands by name

Popular brands