Sofarsolar SOFAR 1100TL Installation And Operating Manual Download Page 77

Page: 77 / 82

TROUBLESHOOTING HANDLING

SOFAR 1100...3300TL-G3

Name

Description

Solution

UnrecoverIPV

Instant

The input current is too

high and has caused an

unrectifiable error

ID74-ID77 are internal inverter

errors, switch the DC switch OFF,

wait 5 minutes and then switch the

DC switch ON. Check whether the

error has been rectified. If not,

please contact the technical

support department.

UnrecoverWR

ITEEEPROM

The EEPROM cannot be

recovered

UnrecoverRE

ADEEPROM

The EEPROM cannot be

recovered

UnrecoverRel

ayFail

The grid relay has a

permanent error

OverTempDe

rating

The inverter has derated

itself due to the

temperature being too

high

Ensure that the installation position

and method both comply with the

necessary requirements of this

user manual. Check whether the

ambient temperature at the

installation location exceeds the

upper limit value. If so, improve the

ventilation in order to reduce the

temperature.

OverFreqDer

ating

The inverter has derated

itself due to the grid

frequency being too high

The inverter automatically reduces

the output power when the

frequency of the electrical grid is

too high. Ensure that the grid

frequency is within the permissible

range.

RemoteDerat

ing

The inverter has derated

itself through the remote

control

The inverter logs ID83 when the

remote power is reduced. Check

the wiring of the remote control

input and output signal connection

on the communication board

Summary of Contents for SOFAR 1100TL



















































































Search results

Summary of Contents for SOFAR 1100TL

Reviews:

Related manuals for SOFAR 1100TL

Brands by name

Popular brands

Sofarsolar SOFAR 1100TL, Installation And Operating Manual

Search results

Summary of Contents for SOFAR 1100TL

Reviews:

Related manuals for SOFAR 1100TL

Brands by name

Popular brands