Sofar 3000TLM-G2 User Manual Download Page 58

Page: 58 / 68

SOFAR 3K~6KTLM-G2

User manual

- 53 -

ID57 OverTempFault_

Inv

The inverter temp is

too high

Ensure the installation position and

installation method meet the requirements of

Section 3.4 of this user manual.

Check whether the ambient temperature of

the installation position exceeds the upper limit.

If yes, improve ventilation to decrease the

temperature.

ID58 OverTempFault_

Boost

The Boost temp is

too high

ID59 OverTempFault_

Env

The environment

temp is too high

ID65 UnrecoverHwAc

OCP

The grid current is

too high, and has

cause unrecoverable

hardware fault

ID65-ID70 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID66

UnrecoverBusO

The bus voltage is

too high, and has

cause unrecoverable

fault

ID67 UnrecoverIacRm

sUnbalance

The grid current is

unbalance, and has

cause unrecoverable

fault

ID68

UnrecoverIpvUn

balance

The input current is

unbalance, and has

cause unrecoverable

fault

ID69

UnrecoverVbus

Unbalance

The bus voltage is

unbalance, and has

cause unrecoverable

fault

ID70

UnrecoverOCPI

nstant

The grid current is

too high, and has

cause unrecoverable

fault

ID71 UnrecoverPvCon

figSetWrong

Incorrect input

mode

Check the input mode(parallel mode/

independent mode) setting of inverter according

to Section 6.3 (C) 6.Input Mode of this user

manual, If it’s incorrect, change it according to

Section 6.3 (A) 10.Set Input mode of this manual

ID74

UnrecoverIPVIn

stant

The input current is

too high, and has

cause unrecoverable

fault

ID74-ID77 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID75

UnrecoverWRIT

EEEPROM

The EEPROM is

unrecoverable

ID76 UnrecoverREAD

EEPROM

The EEPROM is

unrecoverable

ID77

UnrecoverRelay

Fail

Relay has happen

permanent fault

ID81

OverTempDerati

The inverter has

derated because of

the temperature is

Ensure the installation position and

installation method meet the requirements of

Section 3.4 of this user manual. Check whether

Summary of Contents for 3000TLM-G2





































































Search results

Summary of Contents for 3000TLM-G2

Reviews:

Related manuals for 3000TLM-G2

Brands by name

Popular brands

Sofar 3000TLM-G2, User Manual

Search results

Summary of Contents for 3000TLM-G2

Reviews:

Related manuals for 3000TLM-G2

Brands by name

Popular brands