Sofar 3000TLM-G2 User Manual Download Page 16

Page: 16 / 68

SOFAR 3K~6KTLM-G2

User manual

- 11 -

3. Installation

Outlines of this chapter

This topic describes how to install the SOFAR 3K~6KTLM-G2.

Installation notes

3.1. Installation Process

Figure3-1 Installation flowchart

3.2. Checking Before Installation

Checking Outer Packing Materials

Do NOT install the SOFAR

3K~6KTLM-G2

on flammable

material.

Do NOT install the SOFAR

3K~6KTLM-G2

in an area used to

store Flammable or explosive material.

Danger

The enclosure and heat sink are very hot while the inverter is

working, therefore do NOT install the SOFAR

3K~6KTLM-G2

places where you might touch them inadvertently.

Caution

Consider the weight of SOFAR

3K~6KTLM-G2

when

transporting and moving the inverters.

Choose an appropriate mounting position and surface.

Assign at least two persons to install the inverter.

Attention

Start

Check before
installation

Prepare installation
tools

Determine the
installation

Moving

the

inverter

Install

the

rear

panel

Install

the

inverter

End

Summary of Contents for 3000TLM-G2





































































Search results

Summary of Contents for 3000TLM-G2

Reviews:

Related manuals for 3000TLM-G2

Brands by name

Popular brands

Sofar 3000TLM-G2, User Manual

Search results

Summary of Contents for 3000TLM-G2

Reviews:

Related manuals for 3000TLM-G2

Brands by name

Popular brands