Sofar 3000TLM-G2 User Manual Download Page 24

Page: 24 / 68

SOFAR 3K~6KTLM-G2

User manual

- 19 -

4. Electrical Connections

Outlines of this chapter

This topic describes the SOFAR 3K~6KTLM-G2 inverter electrical

connections. Read this part carefully before connecting cables.

NOTE:

Before performing electrical connections, ensure that the DC switch is OFF.

Since the stored electrical charge remains in a capacitor after the DC switch is turned OFF.
So it’s necessary to wait for at least 5 minutes for the capacitor to be electrically discharged.

Installation and maintenance of inverter, must be operated by

professional electrical engineer.

Attention

PV modules generate electric energy when exposed to sunlight and

can create an electrical shock hazard. Therefore, before connecting DC

input power cable, cover PV modules using opaque clot

Danger

In Germany, the PV array maximum voltage must be

≤

600V, max

output of single inverter is 4.6KVA and max output of PV system is

13.8KVA.

SOFAR 3K~6KTLM-G2 has 2 MPPT trackers, all PV modules

connected to the same MPPT should have similar rated electrical

characteristics (including Isc, Voc, Im, Vm, Pm and temperature

coefficients), have the same number of series connected PV modules and

be all in the same orientation (azimuth and tilt angle).

Note

The connected PV modules must have an IEC 61730 Class A rating

Isc PV (absolute maximum)

2*13.2A

Maximum output overcurrent

protection

SOFAR3000TLM-G2

13.7A

SOFAR3600TLM-G2

16.8A

SOFAR4000TLM-G2

18.2A

SOFAR4600TLM-G2

21A

SOFAR5000TLM-G2

22.8A

SOFAR6000TLM-G2

27.3A

The decisive voltage class (DVC)

NOTE:

The DVC is the voltage of a circuit which occurs continuously between any

Summary of Contents for 3000TLM-G2





































































Search results

Summary of Contents for 3000TLM-G2

Reviews:

Related manuals for 3000TLM-G2

Brands by name

Popular brands

Sofar 3000TLM-G2, User Manual

Search results

Summary of Contents for 3000TLM-G2

Reviews:

Related manuals for 3000TLM-G2

Brands by name

Popular brands