Sofar 3000TLM-G2 User Manual Download Page 59

Page: 59 / 68

SOFAR 3K~6KTLM-G2

User manual

- 54 -

too high

the ambient temperature of the installation

position exceeds the upper limit. If yes, improve

ventilation to decrease the temperature.

ID82 OverFreqDeratin

The inverter has

derated because of

the grid frequency is

too high

Inverter automatically reduce the output

power when the frequency of electrical grid is

too high.

ID83

RemoteDerating

The inverter has

derated by the

Remote control

Inverter records ID83 in case of remote

power derating operation. Check the wiring of

remote input and output control signal port on

the communication board according to Section

4.5 of this user manual.

ID84

RemoteOff

The inverter has

shut down because

by the Remote

control

Inverter records ID84 in case of remote

shutdown operation. Check the wiring of remote

input and output control signal port on the

communication board according to Section 4.5 of

this user manual.

ID94 Softwareversioni

snotconsistent

The software in the

control board and

the communication

board is not

consistent

Contact technical support to upgrade

software.

ID95

Communicationb

oardEEPROMfa

ult

The communication

board EEPROM is

fault

ID95~ID96 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID96

RTCclockchipan

omaly

RTC clock chip is

fault

ID97

Invalid Country The country is

invalid

Check the country setting according to

Section 6.3 (C) 5.Country of this user manual, If

it’s incorrect, change it according to Section 6.3

(A) 4.Set Country Code of this manual.

ID98

SDfault

The SD card is fault

Please replace the SD card.

7.2. Maintenance

Inverters generally do not need any daily or routine maintenance. Heat sink

should not be blocked by dust, dirt or any other items. Before the cleaning, make
sure that the DC SWITCH is turned OFF and the circuit breaker between inverter
and electrical grid is turned OFF. Wait at least for 5 minutes before the Cleaning.



Inverter cleaning

Please clean the inverter with an air blower, a dry & soft cloth or a soft bristle

brush. Do NOT clean the inverter with water, corrosive chemicals, detergent, etc.



Heat sink cleaning

Summary of Contents for 3000TLM-G2





































































Search results

Summary of Contents for 3000TLM-G2

Reviews:

Brands by name

Popular brands

Sofar 3000TLM-G2, User Manual

Search results

Summary of Contents for 3000TLM-G2

Reviews:

Brands by name

Popular brands