background image

User Guide

20

Hydronic Heating

Ensure your central heating system is on. Check
the upper rocker switch is to the left (red), the
middle rocker switch to the left (hydronic
heating) and the lower rocker switch either to the
left (normal) or right (boost). Providing the water
temperature in the system is more than 42°C and
the thermostat controlling your central heating
system is calling for heat, your Space Saver will
switch on. Moving the upper rocker switch to its
centre position will turn off the Space Saver.

Electric Heating

Ensure the upper rocker switch is to the left (red),
the middle rocker switch to the right (electric
heating) and the lower rocker switch to the left
(normal) and your Space Saver will switch on. Moving
the lower rocker switch to boost will not increase
the heat output. Moving the upper rocker switch to
its centre position will turn off the Space Saver.

For your safety this Space Saver heater is fitted
with automatic overheat protection. If the heater
stops, turn off the power at the fused spur, wait
5 minutes and switch the power back on.

Air Circulation (summer use)

Ensure your central heating is off. Check the
upper rocker switch is to the right (blue), the
middle rocker switch is either to the left or right
and the lower rocker switch either to the left
(normal) or right (boost). Space Saver will provide
a cooling flow of air. If used in conjunction with a
room thermostat, ensure the thermostat is set to
maximum.

Fault Finding

This Space Saver is covered by a free 5-year parts
and labour guarantee
. Please refer to the Fault
Finding section on page 15 for advice. In the event
of difficulty, please contact us on  01245 324560.
It will be helpful if you do not disconnect the
Space Saver from the central heating system.

Summary of Contents for Hydronic SS2E W

























Reviews: