pipes downwards, placing them gently on the apparatus. Install the charcoal filters clipping the 2 filters clips into place
(Fig.20) and turn the filters upwards. Installation is now complete and the anti-grease filters can be reassembled.
OPERATION
Depending on the model, the unit is equipped with the following commands:
Commands shown in Fig. 21: Button A = turns the lights on/off. Button B = turns the TIMER on/off: press
once to turn the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed
blinks on the display); the timer remains on if the motor speed is changed. Display C = - indicates the selected
motor speed (from 1 to 4); - indicates Timer On when the number blinks; - indicates Filter Alarm when the central
segments is on or blinking.
Button D = makes the motor work (at the last speed selected); pushing the button again, the speeds of the
motor are sequentially selected from 1 to 4; keeping this button pressed for about 2 seconds shuts down the
motor.
Button R = resets the grease filters or charcoal filters; when the filter alarm appears (i.e. when the central
segment on the display goes on), the grease filters must be cleaned (30 hours of operation); when the central
segment starts blinking, the grease filters must be cleaned and the charcoal filters replaced (120 hours of
operation). Obviously, if the hood is not a filtering model and does not have a charcoal filter , clean the grease
filters both when the central segment goes on and when it starts blinking. The filter alarm can be seen when
the motor is off and for about 30 seconds. To reset the hour counter, keep the button pressed for 2 seconds
while the alarm can be seen.
Commands shown in Fig. 22: Button A: turns the lights on/off; every 30 hours of operation the corresponding
pilot lamp (S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the
corresponding pilot lamp (S) flashes to indicate that the grease filters must be cleaned and the charcoal filter
replaced. To restart the hour counter (RESET), hold the button A pressed down for about 1” (while the pilot
lamp S is on). Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding
it down for about 1”, the motor cuts out. Button C: drives the motor in second speed (the corresponding pilot
lamp comes on); when pressing the button a second time (while the pilot lamp is on), the TIMER is activated
and thus the motor stops after 5’ (the pilot lamp flashes). Button D: drives the motor in third speed (the
corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the
TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button E: drives the motor in fourth
speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp
is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes).
Controls shown in Fig.23:
AUTOMATIC OPERATION WITH SENSOR:
Key A : switches the lights on/off. Key B : enables/disables “Automatic” function. When this function is
selected, an “A” appears on the display C, and the speed of the motor increases or decreases depending
on the smoke, odours and gas present in the kitchen. Display C : - indicates the automatic operation of
the sensor (the letter “A” appears);- indicates the motor speed selected automatically by the sensor; indicates
the FILTER ALARM whenever the central segment is illuminated or flashing. Key D : decreases motor
speed / Reset; decreases motor speed to zero (stopping); in any case however, after approximately 1
minute, the hood resumes automatic operation at the speed set by the sensor. Whenever the key is pressed
during the display of filter alarms, a RESET occurs, and the counting of the hours resumes again. Key E
: increases motor speed; in any case however, after approximately 1 minute, the hood resumes automatic
operation at the speed set by the sensor.
Modification of sensor sensitivity: sensor sensitivity can be modified by operating as follows:
- stop the hood by pressing key B. – Simultaneously press keys D and E (the sensor’s sensitivity index will
appear on the display) - Pressing keys D or E, the sensor’s sensitivity will either increase or decrease (1:
minimum sensitivity / 9: maximum sensitivity). – whenever the power supply is interrupted, the sensor will
resume operation with a sensitivity index of 5.
Warning: in order to avoid damaging the sensor, never use silicone products near the hood!
OPERATION AS TRADITIONAL HOOD:
Key A : switches the lights on/off. Display C : - indicates the motor speed selected (from 1 to 4); - indicates
the operation of the Timer when the number is flashing; - indicates filter alarms whenever the central
segment is illuminated or flashing. Key D : decreases motor speed / Stop / Reset; decreases motor speed
to zero (stopping). Whenever the key is pressing during filter alarm display, a RESET occurs, and the
counting of the hours resumes again. Key E : enables the motor / increases motor speed /TIMER. Pressing
this key starts the motor (at the latest speed set); pressing the key again increases motor speed, while
keeping the key pressed down for a few seconds enables the TIMER, and 5 minutes later the motor will
stop (while the number of speed setting selected will simultaneously begin flashing on the display); the
Timer will remain enabled if motor speed is changed. In order to disable the Timer, press the key again.
Pay special attention to the grease filters: if the model purchased has the commands shown in Figure