C
HAPTER
4
| Configuring the Switch
Simple Network Management Protocol
– 129 –
N
OTE
:
The predefined default groups and view can be deleted from the
system. You can then define customized groups and views for the SNMP
clients that require access.
C
ONFIGURING
SNMP
S
YSTEM
AND
T
RAP
S
ETTINGS
To manage the switch through SNMP, you must first enable the protocol
and configure the basic access parameters. To issue trap messages, the
trap function must also be enabled and the destination host specified.
P
ARAMETERS
The following parameters are displayed on the SNMP System Configuration
page:
SNMP System Configuration
◆
Mode
- Enables or disables SNMP service. (Default: Disabled)
◆
Version
- Specifies the SNMP version to use. (Options: SNMP v1,
SNMP v2c, SNMP v3; Default: SNMP v2c)
◆
Read Community
- The community used for read-only access to the
SNMP agent. (Range: 0-255 characters, ASCII characters 33-126 only;
Default: public)
This parameter only applies to SNMPv1 and SNMPv2c. SNMPv3 uses the
User-based Security Model (USM) for authentication and privacy. This
Table 12: SNMP Security Models and Levels
Model Level
Community String Group
Read View
Write View
Security
v1
noAuth
NoPriv
public
default_ro_group
default_view
none
Community string only
v1
noAuth
NoPriv
private
default_rw_group
default_view
default_view
Community string only
v1
noAuth
NoPriv
user defined
user defined
user defined
user defined
Community string only
v2c
noAuth
NoPriv
public
default_ro_group
default_view
none
Community string only
v2c
noAuth
NoPriv
private
default_rw_group
default_view
default_view
Community string only
v2c
noAuth
NoPriv
user defined
user defined
user defined
user defined
Community string only
v3
noAuth
NoPriv
user defined
default_rw_group
default_view
default_view
A user name match only
v3
Auth
NoPriv
user defined
user defined
user defined
user defined
Provides user authentication
via MD5 or SHA algorithms
v3
Auth Priv
user defined
user defined
user defined
user defined
Provides user authentication
via MD5 or SHA algorithms
and data privacy using DES
56-bit encryption
Summary of Contents for 8028L2
