C
HAPTER
8
| Using the Command Line Interface
CLI Command Groups
– 197 –
CLI C
OMMAND
G
ROUPS
The system commands can be broken down into the functional groups
shown below
.
Table 15: Command Group Index
Command Group
Description
Page
System
Configures general system settings, including descriptive
information, user name and password, rebooting the
system, setting the time zone, configuring the log levels
to display, and filtering management access to the switch
through specified IP addresses.
199
IP
Configures IP settings, including IPv4 or IPv6 addresses,
DHCP, DNS, DNS proxy, as well as SNTP
209
Auth
Controls management access through RADIUS or
authentication servers
219
Port
Configures connection parameters for ports, power
saving mode, and cable testing
229
Aggr
Configures static port aggregation, including member
assignment, and load balancing methods
239
LACP
Configures Link Aggregation Control Protocol
245
RSTP
Configures Rapid Spanning Tree Protocol
251
Dot1x
Configures IEEE 802.1X Port Authentication
263
IGMP
Configures IGMP snooping, query, throttling, and filtering
273
LLDP
Configures Link Layer Discovery Protocol
283
MAC
Configures the MAC address table, including learning
mode, aging time, and setting static addresses
291
VLAN
Configures VLAN port members and port attributes
297
PVLAN
Configures private VLANs and isolated ports
303
QoS
Configures quality of service parameters, including
default port queue, default tag assigned to untagged
frames, input rate limiting, output shaping, queue mode,
queue weight, quality control lists, storm control, DSCP
remarking, and DSCP queue mapping
307
ACL
Configures access control lists, including policies,
responses, and rate limiters
319
Mirror
Mirrors data to another port for analysis without affecting
the data passing through or the performance of the
monitored port
327
Config
Saves or restores configuration settings
329
SNMP
Configures SNMP community strings, trap managers, and
basic settings for SNMPv3
331
HTTPS
Enables or disables HTTPS, or automatically redirects
management access from HTTP connections to HTTPS
353
SSH
Enables or disables management access via SSH
357
UPnP
Configures UPnP protocol settings
359
DHCP
Configures DHCP Relay and Option 82 Information
363
Summary of Contents for 8028L2
