background image

 

 

ROOF  ASSEMBLY

 

SELECT:

 

 

6 x 1.720 m Roof Sheets

 

1 x 3.055 m Spouting

 

2 x 1.720 m Barges

 

34 x 50mm Roofing Screws

 

34 x Rivets

 

4 x 50mm Clouts

 

 

12

 

IMPORTANT

 

Use 50mm Clouts only on outside ribs covered by Barge flashings. Predrill 
holes using a 3.5mm drill bit. Use Roofing Screws on all other ribs. Ensure 
screws are not overtightened as this can damage the seals and cause the shed 
to leak.

 

STEP 1:

 

 

• 

Ensure Shed is sitting level and square.

 

 

• 

Lay Roof Sheets on the Top Plates.

 

 

• 

Rivet sheets together at overlaps with 2 x rivets per join

.

 

STEP 2:

 

 

• 

Position the Roof Sheets with front overhang of 130mm at 
each end (

fig. 1

).

 

 

• 

Using 4 x 50mm Clouts, predrill and nail the Roof Sheets to 
the Top Plates through the ribs, at each corner, ensuring ribs 
on the Roof Sheets line up with ribs on the Wall Sheets (

fig.2

).

 

STEP 3:

 

 

• 

Ensure the Front and Back Top Plates are straight. 

 

• 

Screw the roof sheets to the front & back Top Plates, using 1 x 
Roofing Screw per rib. (

fig.2

).

 

STEP 4:

 

 

 

• 

Place barge flashings on roof at end of shed ensuring the diagonal 
trimmed end is at the front. (See diagram on pg 5)

 

 

• 

Rivet the Barge Flashings to the roof and the side wall, using four 
rivets on top of barge and four into the side (

fig.3

).

 

Pan

 

Rib

 

fig.2

 

fig.3

 

X 4

 

X 4

 

Barge

 

Spouting

 

fig.4

 

STEP 7:

 

 

• 

Place spouting in position and rivet to Barge Flashings at each end 
and rivet to roof sheets (1 rivet per 1 sheet) 

(fig.4).

 

SIDE

 

WALL

 

FRONT WALL

 

BACK WALL

 

SIDE

 

WALL

 

TOP PLATE

 

BOTTOM PLATE

 

fig.1

 

130mm

 

130mm

 

IMPORTANT—FOR SHEDS WITH OPTIONAL CLEAR ROOF PANEL 

 

Assemble as below, making sure that the Clear Roof Sheets overlap the stand-
ard roof sheets on both sides. Pre drill and fasten with the 50mm roofing 
screws provided.

 Ensure screws are not overtightened as this can damage the 

seals and cause the shed to leak.

 

Summary of Contents for SM3015

















Reviews: