manualshive.com logo in svg

SmartLine RotaScope Classic Series, Installation And User Instructions Manual

Share
Download
SmartLine RotaScope Classic Series Installation And User Instructions Manual Download Page 84

RotaScope Classic Cabinet 

Manual Version

 1.04             

Date

 23 November 2021  

84 

•

 

The storage times and stored Scope Information will not be lost by performing 
a Hard Reset 

 

Image above shows use of the 

“

Hard Reset Button

”,

 located behind the façade at the top front of the RotaScope 

Cabinet 

5.1.9

 

Starting/Stopping the product operation 

To Start and Stop the products operation, simply remove power to the cabinet via the 
GPO. 

Alternatively 

–

 a fused power switch is located on the side of the IAS (Integrated Air 

System)  which  incorporates  the  electronic  control  devices  of  the  Cabinet  Control 
System. The IAS is located on the top of the cabinet behind the removable façade. 

5.2

 

How to Use the Product Remotely/Automatically 

 

Advanced operations shall only be done by an Authorised Distributor. 

For remote service and access to advanced cabinet settings 

–

 please contact your 

local Authorised Distributor 

5.3

 

What to Do in Emergency and Exceptional Situations 

If the cabinet goes into an alarm state and cannot be rectified, contact your local 
Authorised Distributor  

In case of an emergency: 

•

 

Turn off the device 

•

 

Contact your local Authorised Distributor 

 

 

 

Summary of Contents for RotaScope Classic Series





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands