background image

16

SHOWMATION  AUTOMATION

The STATUS LED’s

indicate the current

state of the system.

The READY led is on

when the failsafe is

up.The system will not

start unless the

READY LED is on.

The RUNNING LED

comes on when the

show is started.

The INTERMISSION

LED is on between

shows.

The INTERLOCK LED

is on when one of the

two Interlocks is

selected

These switches and pushbuttons
control the major show functions.

The  START pushbutton is used to

begin the show. The START LED

will be on while the show is running.

The STOP pushbutton will stop the

show, but will not normally need to
be pushed. The STOP LED will be

on during intermission and will be

rapidly blinking during a film break.

The JOG pushbutton is used to

momentarily run the motor to feed

film as an aid in threading up. Hold it

in to run the motor, and release it to

stop the motor. The JOG pushbutton

is also used as a timer bypass for

the 7 second douser open timer.

The MOTOR and DOUSER toggle

switches are for manual operation

and will not normally be used.

These toggle switches control the

show support functions.

The MASKING and LENS switches

are for manual operation and will not

normally be used unless the
masking or lens is set to the
incorrect format. Push these

switches to the FLAT or SCOPE

positions to select the

correct format.

The CURTAINS and LIGHTS

switches are for manual operation of

the curtains and for bringing the

house lights to maximum in an

emergency situation.

The HOUSE LIGHTS

pushbuttons can be

used to manually

select the lighting

levels desired.

The LED’s in the

pushbuttons indicate

the selected level.

Normally, the levels

are controlled by the

SMART

SHOWGRAMMER

which operates in

conjunction with the

automation system.

In a film break, the automation will shut down the projector. The STOP pushbutton will blink rapidly. After repairing the break

and re-threading, push the START pushbutton to re-start the show. Wait briefly to see that all is running OK and then push the

DOUSER toggle switch to the OPEN position to open the douser.

OPERATOR PANEL QUICK REFERENCE

Summary of Contents for Showmation

















Reviews: