background image

SDS-2500 USER MANUAL V1.0

 

 

© 2018 Smart-e (UK) Ltd 

www.smart-e.co.uk 

PAGE | 29 

 

11

 

INFRA-RED THROUGHPUT 

 

 

Nine 3.5mm stereo jacks are available on the rear of the SDS-2500, as pictured above, these are concerned 
with handling infra-red commands to and from the SDS-2500. 

Infra-red peripherals included with the SDS-2500 are: 

5x IR receivers 

 

4x IR transmitters 

 

 

IR receivers accept infra-red signals from handsets, whilst IR transmitters output infra-red signals to the infra-
red receivers found on the front of consumer electronics such as blu-ray players or satellite boxes. 

The IR receivers can be attached to the IR EXT port or any of the IR INPUT ports, the IR transmitters can be 
attached to the IR OUTPUT ports. 

Infra-red directed at the IR receiver connected to the IR EXT port provides the same functionality as directing 
infra-red at the infra-red receiver on the front of the SDS-2500. This should therefore be used with the provided 
handset  for  the  SDS-2500.  This  allows  for  the SDS-2500  to be  installed  in  a  concealed  location  whilst  still 
having infra-red control by running a infra-red receiver to a location visible to the user. For a full explanation of 
commands which can be executed via this method please refer to section 8 of this manual. 

The remaining IR INPUT and OUTPUT ports allow users to control their sources via infra-red control whilst not 
being in direct sight. The infra-red is switched dependant on which output of the SDS-2500 is switched to which 
input. As an example the image below shows a typical setup with three inputs having the potential to be IR 
controlled,  a  blu-ray  player  and  two  satellite  receiver  boxes.  Each  of  these  devices  has  a  IR  transmitter 
connected from their relevant input port on the rear of the SDS-2500. If the video from the SD DIDIGBOX is 

connected to input 2, then it’s IR transmitter should be connected to IR OUPUT 

port 2. Similarly on the video 

output side if a screen is connected to output 3 of the SDS-

2500, it’s IR receiver should be connected to IR 

INPUT port 3 on the rear of the SDS-2500. 

Summary of Contents for Sds-2500



































Reviews: