background image

INSTALLATION INSTRUCTIONS

FOR EBF-625/EBF-655

SENSOR ACTIVATED FAUCETS

Code No: 9108237

rev. 3 (12/10)

O P T I M A   F A U C E T S

MODELS

EBF-625
EBF-655
Battery powered,
Sensor activated
lavatory Faucets

EBF-625

EBF-655

installation of the Sloan optima plus EBF-625 or EBF-655 Battery 
powered, Sensor activated Faucet makes wash-up totally “hands free” 
providing the ultimate in sanitary protection and automatic operation.
The optima plus faucet uses infrared technology to sense the user’s
presence and turn on a water supply that has been pre-mixed to the
desired water temperature. when the user’s hands are removed from
the invisible beam of light, the water supply automatically turns off. 
in addition, the faucet is powered by four (4) “C” batteries which 
eliminates the need to run any electrical lines to the system.

The Sloan EBF-625 or EBF-655 battery powered, sensor activated
faucet comes complete with an integral faucet and sensor assembly,

control module, alkaline batteries, and all mounting hardware. 
Bak-cheks and a grid strainer are also available as optional equipment. 
The installer should supply 3/8” copper supply tube or flexible hose
connections.

The following instructions serve as a guide when installing the Sloan
EBF-625 or EBF-655 faucet. as always, good safety practices and care
when installing your new faucet.

if further assistance is required, contact your nearest 

Sloan representative office or the Sloan installation

Engineering Department at 1-888-SloaN-14.

LIMITED WARRANTY

Sloan Valve Company warrants its EBF-625 and EBF-655 faucets to be made of first class materials, free from defects of material or workmanship under normal
use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of
three (3) years (one (1) year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or
parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. 
No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve
Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of batteries.

ThErE arE No warraNTiES whiCh ExTEND BEyoND ThE DESCripTioN oN ThE FaCE hErEoF. iN No EVENT iS SloaN ValVE CompaNy rESpoNSiBlE For aNy 
CoNSEquENTial DamagES oF aNy mEaSurE whaTSoEVEr.

Summary of Contents for Optima ETF-600

























Reviews: