manualshive.com logo in svg

SKC Pocket Pump TOUCH, Operating Instructions Manual

Share
Download
SKC Pocket Pump TOUCH Operating Instructions Manual Download Page 23

Form 40017 Rev 1906

Page 23 of 26

www.skcinc.com

Viewing History

History Menu

To review speci

fi

 c sample run summaries directly on the pump screen

From Main Menu: 

 

Touch Device 

> Touch History 

> Touch arrows to scroll

 

 

 

> Touch checkmark to select 

> Touch arrows to scroll 

 

 

 

 

selected summary info

Note:

 The last 16 sample runs can be viewed as Sample Summaries on the pump. A maximum of 4,416 data 

entries can be held in pump memory. This is equal to approximately 70 hours of one-minute averages or 360 
hours of 5-minute averages. To access this data, upload it to DataTrac Pro for Pocket Pump TOUCH Software 
on your PC.

Using Pocket Pump TOUCH with DataTrac Pro for Pocket Pump TOUCH Software

Pocket Pump TOUCH communicates with a laptop/PC via a USB Bluetooth Adapter (Cat. No. 877-94) and DataTrac

®

 Pro for Pocket Pump 

TOUCH Software, which is available as a download (requires Internet connection). Access DataTrac Pro for Pocket Pump TOUCH Software 
using the following procedure:

1.  Check that PC meets DataTrac Pro system requirements.
 

Operating system

Microsoft® Windows® 7, 8, 8.1, or 10

Required software

DataTrac Installer (included with installation)

Minimum display resolution

1024 x 768

Available port

USB 2.0

2.  Install the USB Bluetooth Adapter or “dongle” (Cat. No. 877-94) on laptop/PC according to instructions included with adapter. 
3. 

Browse URL provided in adapter instructions, and download and install the DataTrac Pro Installer on laptop/PC. (A 

fl

 ash drive option 

is available for users without an Internet connection.)

4.  Upon successful installation, DataTrac Pro will launch automatically and a

tt

 empt to 

fi

 nd any active Pocket Pump TOUCH pumps 

within the area.

For further instructions, 

see the DataTrac Pro for Pocket Pump TOUCH User Manual.

Summary of Contents for Pocket Pump TOUCH



























Reviews:

No comments

Brands by name

Popular brands

Load more brands