background image

Form 40017 Rev 1906

Page 1 of 26

www.skcinc.com

Pocket Pump

®

 

 Sample Pump

Cat. No. 220-1000 Series

Operating Instructions

863 Valley View Road, Eighty Four, PA 15330  USA • Tel: 724-941-9701 • www.skcinc.com

Figure 1.

 Pocket Pump TOUCH Physical Feature Overview

Belt clip

Battery 

pack

Battery 
screws

Magnetic charging 

contact/LED

Exhaust (cap installed)

Inlet

Power On/Off 
(manual lock/

unlock) button

Status LEDs

Touch screen/

Display

Table of Contents

 Introduction .......................................................................................................... 2

Checking Pump Kit/Contents

Quick Guide ......................................................................................................... 2

Getting Started ..................................................................................................... 3

Charging the Battery Pack
Battery Charging Notes and Cautions
Turning Pump Power On/Off
Interpreting the Display 
Determining Battery Charge Status
Using the Touch Screen
Navigating Menus and Screens 
Determining Pump Status
Modifying Device Settings 

(Clock Menu: 

Date/Time, 

Units Menu:

 Display Units, 

Screen Menu:

 Dim/Security

)

Operation (Sample Menu: Set Flow, Calibrate, and Sample) ........................ 13

To set pump 

fl

 ow rate

To set up a single sorbent tube train and calibrate – Constant Flow Mode
To set up a multiple sorbent tube train and calibrate – Constant Flow Mode
To set up a multiple sorbent tube train and calibrate – Constant Pressure Mode 
To calibrate pump 

fl

 ow rate prior to bag sampling – Constant Flow Mode

To sample using a single sorbent tube, multiple sorbent tubes, or sample bag
To set up and run a manual sample
To set up and run a timed sample
To run a sample preset

Flow Fault Mode and Display
Viewing History
Using Pocket Pump TOUCH with DataTrac Pro for Pocket Pump TOUCH Software

Maintenance .............................................................................................. 24

Change the Battery Pack
Clean the Touch Screen

Troubleshooting ....................................................................................... 24

Accessories/Replacement Part Ordering ............................................... 25

SKC Limited Warranty and Return Policy .............................................. 25

Appendix: Performance Pro

fi

 le ............................................................... 26

Summary of Contents for Pocket Pump TOUCH



























Reviews: