PL
5/8
PRZECHODZENIE W TRYB CZUWANIA / AKTYWACJI NAPĘDU
4
i
Możliwe jest ustawienie napędu w trybie gotowości (dezaktywacja odbiornika radiowego), aby:
- ograniczyć rozładowanie akumulatora, kiedy panel słoneczny nie może normalnie pracować (pakowanie
rolety, transport, przechowywanie).
- wyeliminować ryzyko fałszywego użycia (pakowanie rolety, transport).
Po zainstalowaniu rolety, normalne działanie zostanie przywrócone poprzez obudzenie napędu
(ponowna aktywacja odbiornika radiowego).
4.1 Tryb czuwania odbiornika radiowego napędu:
i
Napęd może pozostawać w trybie czuwania tylko po zaprogramowaniu pierwszego punktu sterowania w
§ 3 i przed wykonaniem programowania z § 5 (maks. 10 minut) lub w ciągu 10 minut po równoczesnym
odłączeniu napędu od zasilania z akumulatora i z panelu słonecznego).
- Naciskać jednocześnie i
przez 3 sekundy przyciski
„GÓRA”/”STOP” i „DÓŁ”
nadajnika (zaprogramowanego
w §3), napęd będzie pracował przez 0,5 sekundy w jednym
kierunku, a następnie w drugim kierunku. Odbiornik radiowy
napędu został dezaktywowany.
4.2 Obudzenie odbiornika radiowego napędu:
i
Obudzenie jest możliwe tylko wtedy, jeśli panel słoneczny jest podłączony do napędu i oświetlony
(rozproszonym światłem słonecznym, latarką, ... minimalnie).
- Naciskać jednocześnie i
przez ponad 10 sekund przyciski „GÓRA”
i „DÓŁ”
zaprogramowanego nadajnika. Napęd wykonuje obrót
0,5 sekundy w jednym kierunku, a następnie w drugim.
Odbiornik
radiowy napędu został obudzony. Napęd pracuje teraz normalnie.
>>
> 3 s
>>
10 s
PROGRAMOWANIE NOWEGO POZIOMU STEROWANIA (INDYWIDUALNEGO, GRUPOWEGO LUB OGÓLNEGO)
5
5.1- Otworzyć pamięć odbiornika przy pomocy
nadajnika sterowania indywidualnego:
- Naciskać przez około
3 sekundy
na przycisk
PROG
zaprogramowanego wcześniej nadajnika sterowania
indywidualnego. Napęd wykonuje ruch obrotowy
0,5 sekundy w jednym kierunku, a następnie w drugim.
5.2- Zatwierdzić dokonaną czynność z nowego
nadajnika, który chcemy zaprogramować:
- Naciskać przez około
1 sekundę
na przycisk
PROG
nowego nadajnika. Napęd wykonuje ruch obrotowy przez
0,5 sekundy w jednym kierunku, a następnie w drugim.
- Jeśli Państwa nowy poziom sterowania jest sterowaniem grupowym: należy powtórzyć operacje
5.1 i 5.2 dla
każdego napędu grupy.
- Jeśli Państwa nowy poziom sterowania jest sterowaniem ogólnym: należy powtórzyć operacje
5.1 i 5.2 dla
każdego napędu instalacji.
- Aby usunąć nadajnik z pamięci odbiornika napędu należy wykonać operacje
5.1 z zaprogramowanego
nadajnika, a następnie. wykonać operacje 5.2 z nadajnika który chcemy skasować.
1
>>
PROG ≥ 3 s
>>
PROG < 1 s
2