background image

2

www.simplicitymfg.com

 GENERAL WARNINGS

  •  Know the mower controls, safety rules and how 

to stop quickly. READ AND UNDERSTAND THE 
MOWER OPERATOR’S MANUAL.

  •  Read and obey all safety decals.

  •  Wear appropriate ear, eye and breathing 

protection.

  •  Only allow responsible adults, who are familiar with 

the instructions, to operate the unit.

  •  Disengage the electric clutch (PTO). Shut off the 

engine and wait for all moving parts to stop before 
attaching, adjusting, or disconnecting any part of 
the collection system. 

  •  Check the collection system to make sure it is 

bolted tightly to the rider.

  •  DO NOT operate the mower without either the 

entire grass catcher or the deflector in place.

  •  Turn off the PTO switch to disengage the blades 

when not mowing.

  •  DO NOT mow in reverse. Always look down and 

behind before and while travelling in reverse.

  •  DO NOT turn sharply when travelling alongside a 

building or any object. Slow down before turning.

  •  DO NOT carry passengers on the rider.

  •  When blower assembly is removed from the mower 

deck, the deflector must be properly installed.

  •  Collector bags are subject to deterioration 

and wear during normal use.  Inspect the bag 
periodically for tears, holes or weak spots and 
replace with a new bag that meets manufacturer’s 
durability standards.

  •  If the mower stalls or the turbo blower chute plugs: 

1.  Disengage the electric clutch (PTO);

2.  Stop the engine and remove the key;

3.  Set the parking brake, and wait for all moving 

parts to stop.

4.  Remove the foreign object or clear the chute 

with a piece of wood before restarting the 
engine. 

NEVER place hands into blower 

housing to clear jammed object.  Blower 
may rotate when object is removed.

  •  For added rider stability and to prevent tipping or 

loss of control:

a.  Use reduced speed on uneven ground and 

when turning corners.

b.  Reduce loads on hillsides. It is recommended 

that the collection system be kept no more 
than half full when negotiating any slopes. Start 
mowing on slopes when the collection system is 
empty.

c.  Mow across the face of slopes; not up and 

down.

 • 

Never operate on slopes greater than 17.6% 
(10°). 

Read these safety rules and follow them closely. Failure to obey these rules could result in loss 
of control of unit, severe personal injury or death to you, or bystanders, or damage to property or 
equipment.  

This mowing deck is capable of amputating hands and feet and throwing objects.

  

The triangle         in text signifies important cautions or warnings which must be followed.

Safety Rules & Information

Not 

for  

Reproduction

Summary of Contents for 5600352





















Reviews: