background image

www.simplicitymfg.com

Thank you

 for purchasing this quality-built Simplicity product.  We’re pleased 

that you’ve placed your confidence in the Simplicity brand.  When operated and 
maintained according to the instructions in this manual, your Simplicity product 
will provide many years of dependable service.

This manual contains 

safety information to make you aware of the hazards 

and risks associated with this machine and how to avoid them. This machine is 
designed and intended to be used and maintained according to the manual for 
finish cutting of established lawns and is not intended for any other purpose. It 
is important that you read and understand these instructions thoroughly before 
attempting to start or operate this equipment.

Briggs & Stratton Power Products Group, LLC.
Copyright © 2009 Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.

The Simplicity logo is a trademark of Briggs & Stratton
Corporation Milwaukee, WI, USA.

Contact Information:

Briggs & Stratton Corp.
Yard Power Products Group
P.O. Box 702
Milwaukee, WI 53201-0702
www.simplicitymfg.com

DATE PURCHASED

Not 

for  

Reproduction

Summary of Contents for 5600352





















Reviews: