background image

3

SAFETY DECALS

This unit has been designed and manufactured to 
provide you with the safety and reliability you would 
expect from an industry leader in outdoor power 
equipment manufacturing.

Although reading this manual and the safety 
instructions it contains will provide you with the 
necessary basic knowledge to operate this equipment 
safely and effectively, we have placed several safety 
labels on the unit to remind you of this important 
information while you are operating your unit.

Safety Rules & Information

All  DANGER,  WARNING,  CAUTION  and 
instructional messages on your rider and mower 
should be carefully read and obeyed. Personal bodily 
injury can result when these instructions are not 
followed. The information is for your safety and it is 
important! The safety decals below are on your rider 
and mower.

If any of these decals are lost or damaged, replace 
them at once. See your local dealer for replacements.

These labels are easily applied and will act as a 
constant visual reminder to you, and others who may 
use the equipment, to follow the safety instructions 
necessary for safe, effective operation.

1

4

2

3

5

6

7

2 , 5

1 , 7

4

3 , 6

Not 

for  

Reproduction

Summary of Contents for 5600352





















Reviews: