background image

User manual for digital clock SWZ-W610

7.3.4. 

  

    “Func” menu

  

This menu allows to set operation mode:

“dAtE”

- this parameter allows to switch on/off displaying of the date

“yEAr”

- this  parameter allows to switch on/off  displaying of the year while date is 

showed

”oFF”

- displaying of the year is off

”on”

- displaying of the year is on

“thEr”

-   this   parameter   allows   to   switch   on/off   displaying   of   the   temperature.   If 
temperature sensor is not connected to the {

THERM

} input, or if it is damaged, 

the signs „

- - - -

”  will be displayed in place of current temperature.

7.3.5. 

  

    “dCF” menu

  

This menu contains parameters corresponding to cooperation with DCF77 module.

”modE”

- this parameter enables synchronization of internal clock with DCF77 signal, and 

allows to define resting state of the module output. There are available values:

”oFF”

- synchronization is off

”L Lo”

-  synchronization is on, the resting state of DCF module output is LOW 

”L Hi”

-  synchronization is on, the resting state of DCF module output is HIGH

If it is impossible to synchronize clock with DCF signal within 7 days (no signal, or 

errors in received data) the double dot between hour and minutes will start to pulse 

in asymmetrical mode (lighting time much shorter than time of dimming).

”diSP”

- this parameter allows to on/off the signalisation of DCF77 module output state by 

LED ( digital point of the most right digit). Lighting LED means high state of DCF 

output. This parameter can be set to:

”oFF”

- signalisation is off,

”on”

- signalisation is on.

”Sync”

- this submenu allows to check the time of the last synchronization,  the number of 

correct received frames and bits of  DCF77 signal. 

hours:minutes

 

seconds

- the time of last synchronization

day.month.

year 

- the date of last synchronization,

”F NF”

- number of received frames, where NF is the number of 

frames in range 0 to 3

”b NB”

-  number of received bits, where NB is the number of bits 

in range 0 to 59

The   manner   of   presentation   of   these   informations   is   showed   in

  Figure 7.1.   The   first 

information   after   selection  

”Sync”  

(and   pressing   the  

„ENTER”  

button)   is   the   time   of   last 

synchronization (e.g. 23:25:00). Subsequent pressings the [

v

] button, cause in displaying of 

another informations in showed order; the date of last synchronization (e.g. 19

th

 of may 2005), 

the number of correctly received frames  (e.g. 2 frames) and the number of collected bits of 

frame being received (e.g. 47 bits).

17

i

Summary of Contents for SWZ-W610





























Reviews: