background image

User manual for digital clock SWZ-W610

4. 

       DEVICE INSTALLATION

  

The unit has been designed and manufactured in a way assuring a high level of user 

safety and resistance to interference occurring in a typical industrial environment. In order to 

take full advantage of these characteristics installation of the unit must be conducted correctly 

and according to the local regulations.

- Read the basic safety requirements on page 3 prior to starting the installation.

-  Ensure that the power supply network voltage corresponds to the nominal 

voltage stated on the unit’s identification label.

- The load must correspond to the requirements listed in the technical data.

- All installation works must be conducted with a disconnected power supply.

- Protecting the power supply clamps against unauthorized persons must be 

taken into consideration.

4.1. 

  

    UNPACKING

  

After removing the unit from the protective packaging, check for transportation damage. Any 

transportation damage must be immediately reported to the carrier. Also, write down the unit 

serial number on the housing and report the damage to the manufacturer.

Attached with the unit please find:

- user’s manual,

- warranty,

        

4.2. 

  

    ASSEMBLY

  

- Disconnect the power supply prior to starting assembly.

- During installation all available safety requirements should be considered. 

- The mounting method must to preserve high breaking strength, at least  4 times 

the mass of the device.

- Check the correctness of the performed connections prior to switching the unit on. 

To install the device two holes must be prepared (distance like in Figure 4.1) with 

screws or hooks. The device should be installed using its handles placed on the top 

of housing.

6

!

!

!

Summary of Contents for SWZ-W610





























Reviews: