Simex SRP-946, User Manual

Page: 55 / 62

User manual - METER SRP-946
Register Write Range Register description
6Ch Yes 0 ÷ 1
“ HdiS ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
6Dh Yes 0 ÷ 1
“ H r1 ” parameter in “ HOLd ” menu :
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
6Eh Yes 0 ÷ 1
“ H r2 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
6Fh Yes 0 ÷ 1
“ H r3 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
70h Yes 0 ÷ 1
“ H r4 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
71h Yes 0 ÷ 1
“ HOUt ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
77h 5 Yes see descr.
The value of „
X
” coordinate of point
no. 1
of the user defined
characteristic, expressed in 0.1% – higher word
78h 5 Yes see descr.
The value of „ X ” coordinate of point no. 1 of the user defined
characteristic, expressed in 0.1% – lower word
79h 5 Yes see descr.
The value of „ Y ” coordinate of point no. 1 of the user defined
characteristic, no decimal point included – higher word
7Ah 5 Yes see descr.
The value of „ Y ” coordinate of point no. 1 of the user defined
characteristic, no decimal point included – lower word
7Bh
5
÷ C2h
5
Further pairs of „ X ” - „ Y ” coordinates of points no. 2 ÷ 19 of the
user defined characteristic
C3h 5 Yes see descr.
The value of „ X ” coordinate of point no. 20 of the user defined
characteristic, expressed in 0.1% – higher word
C4h 5 Yes see descr.
The value of „
X
” coordinate of point
no. 20
of the user defined
characteristic, expressed in 0.1% – lower word
C5h 5 Yes see descr.
The value of „ Y ” coordinate of point no. 20 of the user defined
characteristic, no decimal point included – higher word
C6h 5 Yes see descr.
The value of „ Y ” coordinate of point no. 20 of the user defined
characteristic, no decimal point included – lower word
D0h
1
Yes 0 ÷ 3
“ Omod ” parameter in “ OUtP ” menu (active current output mode)
0 - current output disabled ; 1 - current output enabled with 4 ÷ 20mA
mode; 2 - current output enabled with 0÷20mA mode ;
3 - current output controlled via RS-485 interface
Yes 0 ÷ 2
“ Omod ” parameter in “ OUtP ” menu (passive current output mode)
0
- current output disabled ;
1
- current output enabled with
4 ÷ 20mA
mode; 2 - current output controlled via RS-485 interface
Yes 0 ÷ 5
“ Omod ” parameter in “ OUtP ” menu (active voltege output mode)
0 - voltage output disabled ; 1 - voltage output enabled with 0 ÷5V
mode; 2 - voltage output enabled with 1÷5V mode ; 3 - voltage
output enabled with 0÷10V mode ; 4 - voltage output enabled with
2÷10V mode ; 5 - voltage output controlled via RS-485 interface
55