background image

For parts or assistance, call Simer Customer Service at 

1-800-468-7867 / 1-800-546-7867

General Information / Installation

3

PERFORMANCE

SPECIFICATIONS

Power Supply Required ..............................115V, 60 HZ

Motor Duty ...................................................Intermittent

Maximum Liquid Temperature..................120° F (49° C)

Individual Branch Circuit Requirement .............15 Amps

Discharge Pipe Size ...............................2” NPT (51mm)

INSTALLATION

NOTICE:

Install pump on a hard, level surface (cement,

asphalt, etc.). Never place pump directly on earth, clay
or gravel surfaces. Basin must be at least 18” (457mm)
in diameter. Be sure that switch can swing through its
entire arc without any obstruction.

Piping

Effluent Applications (for 3/4" (19.1mm) or less solids)

Piping must be 1-1/2" (38.1mm) minimum to carry vol-
ume of pump discharge. Check local codes to determine
if a check valve is required in your system. In cold cli-
mates, check valves are not used to prevent effluent
from freezing in piping.

If using as sump pump, a check valve is recommended.

Sewage Applications (for 2" (51mm) or less solids)

In any case, piping must not be smaller than pump dis-
charge.

When installed in a sewage system, pipe must be capable
of handling semi-solids of at least 2" (51mm) diameter.

The rate of flow in the discharge pipe must keep any
solids present in suspension in the fluid. To meet mini-
mum flow requirements (2 feet (.6 m) per second in dis-
charge line) size pipe as follows:

A Pipe Size Of:

Will Handle a Flow Rate Of:

1-1/2" (38.1mm)

12 GPM (45 LPM)

2" (50.8mm)

21 GPM (79 LPM)

2-1/2" (63.5mm)

30 GPM (114 LPM)

3" (76.2mm)

48 GPM (182 LPM)

Use a 2" (51mm) swing check valve in pump discharge
to prevent backflow of liquid into sump basin. Check
valve should be a free flow valve that will easily pass
solids.

NOTICE: 

For best performance of check valve when

handling solids, do not install it with discharge angled
more than 45° above the horizontal. Do not install
check valve in a vertical position as solids may settle in
valve and prevent opening on startup.

Drill a 3/16" (4.8mm) hole in discharge pipe about 1–2" 
(25.4 - 51mm) above pump discharge connection (but
below check valve) to prevent airlocking the pump.

Electrical

Hazardous voltage. Can shock, burn, or

cause death.

When installing, operating, or servicing

this pump, follow safety instructions listed below.

1.

DO NOT

splice the electrical power cord.

2.

DO NOT

allow electrical cord plug to be sub-

merged.

3.

DO NOT

use extension cords. They are a fire hazard

and can reduce voltage sufficiently to prevent pump-
ing and/or damage motor.

4.

DO NOT

handle or service pump while it is con-

nected to power supply.

5.

DO NOT

remove grounding prong from plug or

modify plug. To protect against electrical shock, the
power cord is a three-wire conductor and includes a
3-prong grounded plug. Plug pump into a 3-wire,
grounded, grounding-type receptacle. Connect pump
according to electrical codes that apply. 

Individual

*Switch Setting

Model

Motor

Full 

Branch Circuit

Cord

in inches (mm)

Number

HP

Load Amps

Required (Amps)

Length

On      

Off

2962

1/2

12.0

15

8’

16" (406)

8" (203)

2963

1/2

12.0

15

8’

14" (356)

6" (152)

MOTOR, SWITCH, & CORD SPECIFICATIONS

GPM (LPM) AT TOTAL FEET (m)

5

10

15

20

Model

(1.5m)

(3m)

(4.6m)

(6.1m)

CAPACITY GALLONS(L)/MINUTE

2962

39

30

16

2

20 Ft.

(148) (114)

(61)

(7.6)

(6.1m)

2963

62

44

11

1

20 Ft.

(235) (167)

(42)

(3.8)

(6.1m)

No flow 

at height

shown

below

Summary of Contents for 2962

















Reviews: