background image

Warranty 3

For parts or assistance, call Simer Customer Service at 1-800-468-7867

Retain Original Receipt For Warranty Eligibility

Limited Warranty

This Limited Warranty is effective June 1, 2011 and replaces all undated warranties and warranties dated before June 1, 2011.
SIMER warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from defects in material and 
workmanship for a period of twelve (12) months from the date of the original consumer purchase. If, within twelve (12) months 
from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at SIMER’s 
option, subject to the terms and conditions set forth herein. Note that this limited warranty applies to manufacturing defects only 
and not to ordinary wear and tear. All mechanical devices need periodic parts and service to perform well. This limited warranty 
does not cover repair when normal use has exhausted the life of a part or the equipment.
The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibility 
is based on purchase date of original product – not the date of replacement under warranty. The warranty is limited to repair or 
replacement of original purchased product only, not replacement product (i.e. one warranty replacement allowed per purchase). 
Purchaser pays all removal, installation, labor, shipping, and incidental charges.
For parts or troubleshooting assistance, DO NOT return product to your retail store. Contact SIMER Customer Service at 
1-800-468-7867.
Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet 
where it was purchased or to the factory immediately after the discovery of any alleged defect. SIMER will subsequently take 
corrective action as promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after 
the warranty expires. Warranty is not transferable and does not apply to products used in commercial/rental applications.

Sewage Pumps

DO NOT return a sewage pump (that has been installed) to your retail store. Contact SIMER Customer Service. Sewage pumps 
that have seen service and been removed carry a contamination hazard with them.
If your sewage pump has failed:
•  Wear rubber gloves when handling the pump;
•  For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;
•  Dispose of the pump according to local disposal ordinances.

Exceptions to the Twelve (12) Month Limited Warranty

Product

Warranty Period

BW85P, M40P

90 days

2115, 2300, 2310, 2330, 2943, 2955, 2956, 2957, A5500

2 Years

4” Submersible Well Pumps, 2945, 2958, 2975PC, 3075SS, 3963, 3984, 3995

3 Years

Pre-Charged Pressure Tanks, 3985, 3986, 3988, 3989, 5910, 5950, 5955, 5965, 5975

5 Years

General Terms and Conditions; Limitation of Remedies

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not 
apply to the following: (1) acts of God; (2) products which, in SIMER’s sole judgement, have been subject to negligence, abuse, 
accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation, maintenance or storage; (4) 
atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or other foreign materials in the system, 
or operation at pressures in excess of recommended maximums.
This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive remedy for defective products.
SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, 
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE. THE FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an 
implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights 
and You may also have other rights which vary from state to state.

SIMER • 293 Wright Street • Delavan, WI U.S.A. 53115 

Phone: 1-800-468-7867 • Fax: 1-800-390-5351 • Web Site: SimerPump.com

Summary of Contents for 2806E

































Reviews: